При запуске отключается питание

Post new topic   Reply to topic    DD-WRT Forum Index -> Использование и установка DD-WRT
Author Message
mittus
DD-WRT Novice


Joined: 29 Oct 2017
Posts: 4

PostPosted: Sun Oct 29, 2017 1:42    Post subject: При запуске отключается питание Reply with quote
Здравствуйте!

Роутер: Linksys EA6400
Прошивка: DD-WRT v3.0-r33215 std (08/25/17)
Linux 4.4.83 #1923 SMP Thu Aug 24 21:09:13 CEST 2017 armv7l

Никак не могу решить проблему с выключением USB-порта при загрузке роутера. Всё, что мне от него нужно - это включенное питание. При запуске роутера питание на USB-порт идёт, но как только DD-WRT загружается, оно пропадает. В настройках Services -> USV параметр Core USB Support включен. Включить питание USB могу только зайдя в это меню и нажав Apply Settings.

Подскажите пожалуйста, как можно решить эту проблему? Возможно ли ограничить доступ прошивки к управлению питанием USB, или-же запускать обновление настроек по крону (если возможно - просьба дать команды для telnet, т.к. я в этом профан).

Спасибо!
Sponsor
vasek00
DD-WRT Guru


Joined: 06 Nov 2010
Posts: 3312

PostPosted: Mon Oct 30, 2017 6:19    Post subject: Re: При запуске отключается питан Reply with quote
Не много не понятна фишка.


Проверьте параметры через телнет следующих переменных :
Code:
root@My:~# nvram show | grep usb
usb_mntpoint=mnt
usb_storage=1
usb_automnt=1
usb_mntopt=
usb_mntjffs=
usb_ses_umount=0
usb_usb2=1
usb_runonmount=
usb_uhci=0
usb_ohci=0
usb_enable=1
usb_printer=0
root@My:~#

если нет то выполните для нужных параметров
Code:
nvram set usb_storage=1
nvram set usb_automnt=1
nvram set usb_enable=1
nvram commit
reboot
mittus
DD-WRT Novice


Joined: 29 Oct 2017
Posts: 4

PostPosted: Mon Oct 30, 2017 9:09    Post subject: Re: При запуске отключается питан Reply with quote
vasek00 wrote:
Не много не понятна фишка.


Проверьте параметры через телнет следующих переменных :
Code:
root@My:~# nvram show | grep usb
usb_mntpoint=mnt
usb_storage=1
usb_automnt=1
usb_mntopt=
usb_mntjffs=
usb_ses_umount=0
usb_usb2=1
usb_runonmount=
usb_uhci=0
usb_ohci=0
usb_enable=1
usb_printer=0
root@My:~#

если нет то выполните для нужных параметров
Code:
nvram set usb_storage=1
nvram set usb_automnt=1
nvram set usb_enable=1
nvram commit
reboot


Добавил включение параметров usb_storrage и usb_autmnt, usb_enable был активен. Перезагрузился - USB-порт сначала дает питание, потом при окончательной загрузке роутера (когда становится доступной сеть wifi) перестает работать. Также как и было до того.

Вот мой список параметров:
Code:
root@DD-WRT:~# nvram show | grep usb
size: 35217 bytes (30319 left)
usb_automnt=1
usb_ohci=0
usb_storage=1
usb_mntpoint=mnt
usb_runonmount=
usb_mntopt=
usb_printer=0
usb_usb2=0
usb_ip=0
usb_mntjffs=
usb_uhci=0
gpio10=usbport2
usb_ses_umount=0
usb_enable=1
root@DD-WRT:~#


Если это как-то влияет, на роутере USB 3-й версии.
vasek00
DD-WRT Guru


Joined: 06 Nov 2010
Posts: 3312

PostPosted: Tue Oct 31, 2017 6:11    Post subject: Re: При запуске отключается питан Reply with quote
1. Вывод dmesg
2. Откат на 2-3 релиза назад.
mittus
DD-WRT Novice


Joined: 29 Oct 2017
Posts: 4

PostPosted: Tue Oct 31, 2017 8:25    Post subject: Re: При запуске отключается питан Reply with quote
vasek00 wrote:
1. Вывод dmesg
2. Откат на 2-3 релиза назад.


Code:

root@DD-WRT:~# dmesg | cat
console [ttyS0] enabled
serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117, base_baud = 6250000) is a 16550
brd: module loaded
loop: module loaded
bcmsflash: found no supported devices
The first offset=200000, 2nd offset=2100000
Boot partition size = 524288(0x80000)
lookup_nflash_rootfs_offset: offset = 0x200000 size = 0x1f00000, 0x20000
found TRX Header on nflash!
nflash: squash filesystem with lzma found at block 29
lookup_nflash_rootfs_offset: offset = 0x2100000 size = 0x1b00000, 0x20000
found TRX Header on nflash!
nflash: squash filesystem with lzma found at block 277
Creating 6 MTD partitions on "nflash":
0x000000000000-0x000000080000 : "boot"
0x000000080000-0x000000180000 : "nvram"
0x000000200000-0x000002100000 : "linux"
0x0000003a0000-0x000002100000 : "rootfs"
0x000002100000-0x000003c00000 : "linux2"
0x0000022a0000-0x000003c00000 : "rootfs2"
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
GACT probability NOT on
Mirror/redirect action on
Simple TC action Loaded
netem: version 1.3
u32 classifier
    Performance counters on
    input device check on
    Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1941 buckets, 7764 max)
nf_conntrack_rtsp v0.7 loading
xt_time: kernel timezone is -0000
ip_set: protocol 6
gre: GRE over IPv4 demultiplexor driver
nf_nat_rtsp v0.7 loading
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 17
bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
Bridge firewalling registered
8021q: 802.1Q VLAN Support v1.8
Registering SWP/SWPB emulation handler
max nvram space = 131072
read 65536 bytes to offset 0
Key type encrypted registered
Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012
nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
nand: AMD/Spansion NAND 128MiB 3,3V 8-bit
nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
Spare area=64 eccbytes 56, ecc bytes located at:
 2 3 4 5 6 7 8 9 10 11 12 13 14 15 18 19 20 21 22 23 24 25 26 27 28 29 30 31 34 35 36 37 38 39 40 41 42 43 44 45 46 47 50 51 52 53 54 55 56 57 58 59 60 61 62 63
Available 7 bytes at (off,len):
(1,1) (16,2) (32,2) (48,2) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0) (0,0)
Scanning device for bad blocks
Options: NO_SUBPAGE_WRITE,
Creating 1 MTD partitions on "brcmnand":
0x000004000000-0x000008000000 : "ddwrt"
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
Freeing unused kernel memory: 344K
et: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
et_module_init: passivemode set to 0x0
et_module_init: txworkq set to 0x0
et_module_init: et_txq_thresh set to 0x400
et_module_init: et_rxlazy_timeout set to 0x3e8
et_module_init: et_rxlazy_framecnt set to 0x20
et_module_init: et_rxlazy_dyn_thresh set to 0
ET Corerev 4
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.89.21 (r524987)
roboswitch: Probing device 'eth0'
roboswitch: trying a 53011! at eth0
detected CPU Port is 5
roboswitch: found a 53011! at eth0
detected CPU Port is 5
wl_module_init: passivemode set to 0x0
wl_module_init: txworkq set to 0x0
PCI: Enabling device 0001:01:00.0 (0140 -> 0142)
eth1: Broadcom BCM43227 802.11 Wireless Controller 7.14.89.21 (r524987)
eth2: Broadcom BCM4360 802.11 Wireless Controller 7.14.89.21 (r524987)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-pci 0000:00:0a.1: EHCI Host Controller
ehci-pci 0000:00:0a.1: new USB bus registered, assigned bus number 1
ehci-pci 0000:00:0a.1: irq 111, io mem 0x18021000
ehci-pci 0000:00:0a.1: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-pci: OHCI PCI platform driver
ohci-pci 0000:00:0a.0: OHCI PCI host controller
ohci-pci 0000:00:0a.0: new USB bus registered, assigned bus number 2
ohci-pci 0000:00:0a.0: irq 111, io mem 0x18022000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
xhci_hcd 0000:00:0b.0: xHCI Host Controller
xhci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 3
xhci_hcd 0000:00:0b.0: hcc params 0x02501164 hci version 0x100 quirks 0x00000010
hub 3-0:1.0: USB hub found
hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19)
xhci_hcd 0000:00:0b.0: xHCI Host Controller
xhci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 4
usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
SCSI subsystem initialized
usbcore: registered new interface driver usb-storage
eth0: mixed HW and IP checksum settings.
device br0 entered promiscuous mode
device vlan1 entered promiscuous mode
device eth0 entered promiscuous mode
br0: port 1(vlan1) entered forwarding state
br0: port 1(vlan1) entered forwarding state
device eth1 entered promiscuous mode
br0: port 2(eth1) entered forwarding state
br0: port 2(eth1) entered forwarding state
device eth2 entered promiscuous mode
br0: port 3(eth2) entered forwarding state
br0: port 3(eth2) entered forwarding state
device br0 left promiscuous mode
device br0 entered promiscuous mode
device br0 left promiscuous mode
device vlan2 entered promiscuous mode
random: dnsmasq: uninitialized urandom read (128 bytes read, 65 bits of entropy available)
random: dnsmasq: uninitialized urandom read (48 bytes read, 65 bits of entropy available)
device vlan2 left promiscuous mode
NET: Registered protocol family 10
l2tp_core: L2TP core driver, V2.0
l2tp_netlink: L2TP netlink interface
l2tp_ppp: PPPoL2TP kernel driver, V2.0
random: xl2tpd: uninitialized urandom read (2 bytes read, 77 bits of entropy available)
random: xl2tpd: uninitialized urandom read (2 bytes read, 77 bits of entropy available)
random: nas: uninitialized urandom read (16 bytes read, 82 bits of entropy available)
random: nas: uninitialized urandom read (16 bytes read, 82 bits of entropy available)
random: nas: uninitialized urandom read (16 bytes read, 82 bits of entropy available)
random: nas: uninitialized urandom read (16 bytes read, 82 bits of entropy available)
random: nas: uninitialized urandom read (16 bytes read, 82 bits of entropy available)
random: nas: uninitialized urandom read (16 bytes read, 82 bits of entropy available)
br0: port 1(vlan1) entered forwarding state
br0: port 2(eth1) entered forwarding state
br0: port 3(eth2) entered forwarding state
random: nonblocking pool is initialized
device vlan2 entered promiscuous mode
device vlan2 left promiscuous mode
nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
br0: received packet on eth2 with own address as source address
......
br0: received packet on eth1 with own address as source address


Откат точно не поможет, так как я обновлялся уже с прошивки версии еще 2016 года (не помню, какой именно), но была та же история. USB можно было включить только при входе в интерфейс и нажатии кнопки "Apply changes" в разделе USB.
vasek00
DD-WRT Guru


Joined: 06 Nov 2010
Posts: 3312

PostPosted: Tue Oct 31, 2017 13:08    Post subject: Re: При запуске отключается питан Reply with quote
Сразу скажу broadcom - не щупал.

Для начала у вас
1.
usb_automnt=1
usb_storage=1
usb_mntpoint=mnt
gpio10=usbport2
usb_enable=1

automnt - автомонтирование
mntpoint - по умолчанию куда, точка монтирования
usb_enable - разрешено

2. dmesg не чего не говорит о том что что-то включено в USB порт

Code:

usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-pci 0000:00:0a.1: EHCI Host Controller
ehci-pci 0000:00:0a.1: new USB bus registered, assigned bus number 1
ehci-pci 0000:00:0a.1: irq 111, io mem 0x18021000
ehci-pci 0000:00:0a.1: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-pci: OHCI PCI platform driver
ohci-pci 0000:00:0a.0: OHCI PCI host controller
ohci-pci 0000:00:0a.0: new USB bus registered, assigned bus number 2
ohci-pci 0000:00:0a.0: irq 111, io mem 0x18022000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
xhci_hcd 0000:00:0b.0: xHCI Host Controller
xhci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 3
xhci_hcd 0000:00:0b.0: hcc params 0x02501164 hci version 0x100 quirks 0x00000010
hub 3-0:1.0: USB hub found
hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19)
xhci_hcd 0000:00:0b.0: xHCI Host Controller
xhci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 4
usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
SCSI subsystem initialized
usbcore: registered new interface driver usb-storage


из чего можно предположить, что странный формат или разделы на носителе.

3. вы говорите что USB 3-й версии.

4. смущает, что при "Apply" все якобы монтируется

Проверим еще
1. после перезапуска что-то есть в
Code:
root@My:/proc/bus/usb# cat devices

при включенном носителе в USB порт
2. так же вопрос по "gpio10=usbport2"
пробегала информация про BCM4708A0@800
Code:
 
gpio enable 9
is the USB 3.0 port

gpio enable 10
is the USB 2.0 port

вы же говорите USB3 используете попробуем на USB3 и опять dmesg, смена переменной через nvram.
3. Можете поднять релиз с вашего
Quote:
Прошивка: DD-WRT v3.0-r33215 std (08/25/17)

хотя бы не ниже 33492
mittus
DD-WRT Novice


Joined: 29 Oct 2017
Posts: 4

PostPosted: Sun Nov 26, 2017 14:45    Post subject: Re: При запуске отключается питан Reply with quote
vasek00 wrote:
Сразу скажу broadcom - не щупал.

Для начала у вас
1.
usb_automnt=1
usb_storage=1
usb_mntpoint=mnt
gpio10=usbport2
usb_enable=1

automnt - автомонтирование
mntpoint - по умолчанию куда, точка монтирования
usb_enable - разрешено

2. dmesg не чего не говорит о том что что-то включено в USB порт

Code:

usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-pci 0000:00:0a.1: EHCI Host Controller
ehci-pci 0000:00:0a.1: new USB bus registered, assigned bus number 1
ehci-pci 0000:00:0a.1: irq 111, io mem 0x18021000
ehci-pci 0000:00:0a.1: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-pci: OHCI PCI platform driver
ohci-pci 0000:00:0a.0: OHCI PCI host controller
ohci-pci 0000:00:0a.0: new USB bus registered, assigned bus number 2
ohci-pci 0000:00:0a.0: irq 111, io mem 0x18022000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
xhci_hcd 0000:00:0b.0: xHCI Host Controller
xhci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 3
xhci_hcd 0000:00:0b.0: hcc params 0x02501164 hci version 0x100 quirks 0x00000010
hub 3-0:1.0: USB hub found
hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19)
xhci_hcd 0000:00:0b.0: xHCI Host Controller
xhci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 4
usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
SCSI subsystem initialized
usbcore: registered new interface driver usb-storage


из чего можно предположить, что странный формат или разделы на носителе.

3. вы говорите что USB 3-й версии.

4. смущает, что при "Apply" все якобы монтируется

Проверим еще
1. после перезапуска что-то есть в
Code:
root@My:/proc/bus/usb# cat devices

при включенном носителе в USB порт
2. так же вопрос по "gpio10=usbport2"
пробегала информация про BCM4708A0@800
Code:
 
gpio enable 9
is the USB 3.0 port

gpio enable 10
is the USB 2.0 port

вы же говорите USB3 используете попробуем на USB3 и опять dmesg, смена переменной через nvram.
3. Можете поднять релиз с вашего
Quote:
Прошивка: DD-WRT v3.0-r33215 std (08/25/17)

хотя бы не ниже 33492


Помогло обновление прошивки до версии DD-WRT v3.0-r33555 std (10/20/17). Более поздние версии до DD-WRT v3.0-r33772 std (11/26/17) включительно пытался ставить, но там не подключалось соединение с интернетом через L2TP.

Спасибо за помощь!
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Использование и установка DD-WRT All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum