I am attempting to follow the VLAN configuration via GUI - 1 CPU port guide, however I do not see the "Switch Config" tab when I select "Setup". The only tabs I can see are: Basic Setup, IPv6, DDNS, Mac Address Clone, Advanced Routing, Networking, and Tunnels.
I am very new to dd-wrt and just set up the router today with dd-wrt, so I imagine I am missing a very elementary step. Thanks for any advice you may provide.
Did you reset and reboot (twice?), clear browser cache, or do a CTRL+F5? Was it visible in a previous build? _________________ "The woods are lovely, dark and deep,
But I have promises to keep,
And miles to go before I sleep,
And miles to go before I sleep." - Robert Frost
"I am one of the noticeable ones - notice me" - Dale Frances McKenzie Bozzio
Yes, I have reset and reboot twice in the GUI via Administration -> Factory Defaults; cleared the browser cache; and forced the page to reload (I am on a Mac so the keyboard shortcut was command + R). Is there a different reset method I should attempt?
This is the first build I have tried using with dd-wrt so I am not sure if it was visible in a previous build. Though I did see it mentioned in the 1 CPU VLAN GUI Configuration guide.
The router does not have anything connected to the WAN port. I didn't think that should be an issue, but mentioning it just in case.
On occasion I have had to put in the full URL to the Switch Config tab manually. Try this:
http://RouterIP/Vlan.asp
Once you turn it on, it should show back up after a reboot. _________________ Linksys EA8500 (Internet Gateway, AP/VAP) - DD-WRT r53562
Features in use: WDS-AP, Multiple VLANs, Samba, WireGuard, Entware: mqtt, mlocate
Wireless 5ghz only
Netgear R7800 (WDS-AP, WAP, VAP) - DD-WRT r55779
Features in use: multiple VLANs over single trunk port
Linksys EA8500 WDS Station x2 - DD-WRT r55799
Netgear R6400v2 WAP, VAP 2.4ghz only w/VLANs over single trunk port. DD-WRT r55779
OSes: Fedora 38, 9 RPis (2,3,4,5), 20 ESP8266s: Straight from Amiga to Linux in '94, never having owned a Windows PC.
Safari for Mac: There is no simple keyboard shortcut to force a hard refresh. Instead, press Command+Option+E to empty the cache, then hold down Shift and click Reload in the toolbar.
x2 on the following suggestion:
lexridge wrote:
On occasion I have had to put in the full URL to the Switch Config tab manually. Try this:
http://RouterIP/Vlan.asp
Once you turn it on, it should show back up after a reboot.
_________________ "The woods are lovely, dark and deep,
But I have promises to keep,
And miles to go before I sleep,
And miles to go before I sleep." - Robert Frost
"I am one of the noticeable ones - notice me" - Dale Frances McKenzie Bozzio
Joined: 16 Nov 2015 Posts: 6447 Location: UK, London, just across the river..
Posted: Sun Dec 24, 2023 7:31 Post subject:
it could be missing by mistake...as it was removed from those devices with dumb switch..unless your router has one too..where WAN port is part of the switch and ect... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913