[BurtJ]

K26:
Router: ASUS RT-N12 D1
Firmware:dd-wrt.v24-26622_NEWD-2_K2.6_mega.bin
Status: Working
Reset: no
Previous:Build 26587
Error:Same as Previous,WiFi LED not working/Wireless Packet Info reports Tx errors, but wifi seems ok when I use it.

K3X:
Router: ASUS RT-N12 D1
Firmware:dd-wrt.v24-26622_NEWD-2_K3.x_mega.bin
Status: Working with issue
Reset: yes
Previous:dd-wrt.v24-26622_NEWD-2_K2.6_mega.bin-->dd-wrt.v24-21605_NEWD-2_K3.x_mega.bin(do a Restore Factory Defaults)-->dd-wrt.v24-26622_NEWD-2_K3.x_mega.bin(do a Restore Factory Defaults again)
issue:
If I turn off WiFi radio(ex: set Wireless Network Mode=disable/Enable Radio Time Restrictions and when entering off time),the router has high chance to stop responding or/and then reboot by itself.
(Still has ping responding till reboot,but no web access and NAT/Internet connection seems broken too)

I watched the top command and found that the router runs resetbutton(I didn't press any thing) command automaticlly and do a shutdown/reboot.

If I keep WiFi on,it seems runs ok.
This issue seems also happens in previous K3X build but I just found how it stops responding at this build.

[jrscs]

Build 26622 - Previous 26587

RT-AC68R - primary router/gateway
asus_rt-ac68u-firmware.trx
2.4Ghz (NG-mixed) with 40Mhz channel width: OK
5Ghz (Mixed) with 80Mhz channel width: OK
Guest-Vlan 2.4Ghz: OK
SSH: OK
Telnet: OK
Port Forward: OK
WOL over the Internet: OK
VNC Repeater: OK
USB 2.0 storage ext3 mount to JFFS: OK
USB 3.0 storage NTFS mount to MNT: OK
NAS Samba shared drive: OK
PPTP Server: OK
Wi-viz 2.4Ghz & 5Ghz: OK
Power Up Reset: Yes (before and after flash)
Status: Working
Errors: OK

RT-AC66U - primary router/gateway
dd-wrt-26622-Asus_RT-AC66.trx
2.4Ghz (NG-mixed) with 40Mhz channel width: OK
5Ghz (Mixed) with 80Mhz channel width: OK
Guest-Vlan 2.4Ghz: OK
SSH: OK
Telnet: OK
Port Forward: OK
WOL over the Internet: OK
USB storage ext3 mount to JFFS: OK
USB storage NTFS mount to MNT: OK
NAS Samba shared drive: OK
PPTP Server: OK
Wi-viz 2.4Ghz & 5Ghz: OK
Power Up Reset: No (before and after flash), will reset 5.0 GHz radio to 2.4 GHz radio
Status: Working
Errors:
*** Builds after 26339 when erasing NVRAM in telnet session or Power UP Reset, resets 5.0 GHz radio to 2.4 GHz radios – To recover return to 26339 ***
*** Builds after 26339 use the GUI to reset NVRAM to Factory Defaults ***

[diabolo]

RT-N18U primary router/gateway
asus_rt-n18u-firmware.trx (Build 26622) previous (build 26490)
Telnet: OK
USB 2.0/3.0 storage fat32 mount to MNT: OK
NAS Samba shared drive: OK
Openvpn Server: OK
Power Up Reset: No
Status: Working
Errors: None

[Dum Dum]

Router Model: r7000
Status: working
Reset: yes (upgraded from 25974)
Errors: none

Additional services in use:
OpenVPN server, USB storage, Adblocking, 2.4Ghz VAP "Guest" with additional DHCP server

[chris_oakes]

Router: Netgear r6300
Firmware: 03-31-2015-r26622/
Status: Working
Reset: No
Errors: None
Previous: 03-27-2015-r26372/

was glad to see Kong fixed Radvd issue.

[latinpapie]

I uploaded this build to an RT-AC66U, and my only issue is my 2.4ghz gets doubled in the settings. I dont have an option for the 5Ghz. Ive tried to hard reset multiple times but no luck.

[harpseal]

Router: Netgear r6300v1
Firmware: 26622_NEWD-2_K3.x_mega-R6300
Status: Working- with issue
Reset: No
Previous: 26587

The 2.4GHz has twice suddenly stopped broadcasting on it's own on my R6300v1 while running build 26622. This seems to take a number of hours to happen, maybe 8+. Note: the "disappearance" of 2.4GHz happened on the previous build (26587) also but not on my next previous built 25015. According to the router status screens everything is working fine, but 2.4GHz transmission errors are pretty high (I do live in a very high congestion 2.4GHz area so usually I don't count the errors for much, but this seemed to really uptick AFTER the radio stops working. 2.4GHz performance, when working, seems fine.

5GHz works fine and keeps on ticking.

Otherwise seems like a pretty stellar build with better performance than 24200 that I was running for quite a while (especially LAN performance).

Also note, in a different recent thread a couple other 6300 users have noticed this in the new builds so I am not the only one.

[vicktor_1]

Router: WNDR 4000
Build: DD-WRT v24-sp2 (04/01/15) mega - build 26635M K3
Status: working but no DLNA
Previos: 22200

Hi All,

I do not see the settings for DLNA. Is it missing?

Regards,

Viktor

[AreA]

Router: Linksys E2500
Firmware: 26622_NEWD-2_K3.x_mega-e2500
Status: Working with errors
Reset: yes
Previous: 26138

ERRORS : The WAN port does not work! WAN IP: 0.0.0.0 while the network cable is connected (green LED)