This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 27456_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build. _________________ [I prefer answere in whole sentence]
WAP54G v3.1
DD-WRT v3.0-r27456 (06/27/15) micro
Linux 2.4.37 #41238 Sat Jun 27 04:01:57 CEST 2015 mips
NO reset from
DD-WRT v3.0-r27453 (06/25/15) micro
Linux 2.4.37 #41190 Thu Jun 25 06:59:07 CEST 2015 mips
Update wireless thru main router to this WAP54G in Repeater mode to its WAN address
on port 8080. After 5 minutes I could see it wirelessly but could not connect.
Had to go out and reboot it. (its out in the RV)
Working great - no problems
Uptime 43 min
--
Linksys E2500
DD-WRT v3.0-r27456 (06/27/15) mega
Linux 3.10.81 #8815 Sat Jun 27 08:15:50 CEST 2015 mips
[dd-wrt.v24-27456_NEWD-2_K3.x_mega-e2500.bin]
NO reset - update live - previous
DD-WRT v3.0-r27453 (06/25/15) mega
Linux 3.10.81 #8787 Thu Jun 25 11:20:45 CEST 2015 mips
WAN DHCP
WAN MAC clone
22 Static leases
port range forward
local DNS
VPN pass thru
2.4 GHz, NG-Mixed, Wide HT40, ch 5 lower
WPA2 Personal - AES, renewal interval 3300 seconds
Wireless MAC Filter
Restricted Guest network, br1
Posted: Sun Jun 28, 2015 19:44 Post subject: Asus RT-AC68U
asus_rt-ac68u-firmware r27456 (previous r27396)
Kernel: 3.10.81 #4346 SMP Thu Jun 25 08:12:03 CEST 2015 armv7l GNU/Linux
2.4Ghz (NG-mixed) with 40Mhz channel width: Ok
5Ghz (Mixed) with 80Mhz channel width: Ok
SSH: Ok
Telnet: Disabled but tested to work
USB 2.0 storage ext3 mount to JFFS: Ok
USB 3.0 storage EXT3 mount to /mnt: Ok
Samba shared drive: Ok
Site Survey: Ok
Wi-viz 2.4Ghz & 5Ghz: No, not working in the last many releases
Reset: No, not since R27332
Status: Ok
Uptime: 13 minutes
Posted: Mon Jun 29, 2015 15:23 Post subject: buffalo_wzr-600dhp
Router Model: Buffalo WZR-HP-AG300H (actually a wzr-600dhp)
Firmware Version: DD-WRT v3.0-r27456 (06/27/15) std
Kernel Version: Linux 3.10.81 #5128 Sat Jun 27 01:24:03 CEST 2015 mips
Using the wzr-600dhp as a standard WAN automatic DHCP connected to a cable modem; all is good except:
Unit reports itself as the wrong model number
httpd either never starts or crashes on startup. To get httpd to run after each reboot, I must telnet to the router and execute 'httpd -p 80'
WNDR3700v3
DD-WRT v3.0-r27456 (06/27/15) mega
Linux 2.6.24.111 #26172 Sat Jun 27 00:52:16 CEST 2015 mips
[dd-wrt.v24-27456_NEWD-2_K2.6_mega-nv64k.bin]
GUI reset before & after - previous
DD-WRT v3.0-r27453 (06/25/15) mega
Linux 3.10.81 #8787 Thu Jun 25 11:20:45 CEST 2015 mips
[dd-wrt.v24-27453_NEWD-2_K3.x_mega-nv64k.bin]
RB mode on 2.4 GHz NOT working. Kills the bridge if create a VAP. Same behavior as the WAP54.
Reboot makes NO difference.
It will briefly show in wireless status It's there -- then it ain't.
Remove VAP and bridge reconnects.
user.info syslog: NAS : NAS wan (wl0 interface) successfully started
user.info syslog: nas : NAS daemon successfully stopped
Install [dd-wrt.v24-27456_NEWD-2_K3.x_mega-nv64k.bin] over broken RB.
Linux 3.10.81 #8815 Sat Jun 27 08:15:50 CEST 2015 mips
RB working --- enable WPA2 aes on VAP - could only connect after reboot then all good.
No errors with the K3.x
Funny stuff in logs sometimes
Code:
kern.emerg kernel: found nvram
That's nice to know - glad it found it
Repeater Bridge working great on K3.x !!!
GUI reset --
Looks like broadcom did not get the new 'Recursive DNS Resolving' feature I got on the atheros WNDR3700v4.
Restore repeater Bridge from backup -- all worked fine!
Pic of some noticeable differences in K2.6 & K3.x on this box -- other than one works good and the other don't -
Router: Netgear R7000
Firmware: 27456
Status: Not working (bricked)
Reset: No
Errors: router doesn't boot after flashing
Previous: 27360
After flashing only the power led is on (orange).
I tried to flash the stock firmware via TFTP, but I can ping the router for about 10 seconds and then I get a timeout.
I've ordered the USB to serial cable from amazon.
After turning router on I can stop the loading process and start the TFTPD.
Then the firmware was successfully send to the router, but on the router I get a checksum mismatch error:
I tried to re-download the firmware, and also with older firmware versions. But got same error every time.
I can't de-brick my router. Seems to be finally bricked .
Joined: 11 Nov 2006 Posts: 41 Location: Orlando, FL USA
Posted: Wed Jul 01, 2015 13:49 Post subject:
Web Flashed from 27435
Reset - No
Issues - WiViz doesn't show anything
Samba - working with EXT4 500GB USB 3.0 drive
Router Name R7000
Router Model Netgear R7000
Firmware Version DD-WRT v3.0-r27456 (06/27/15) std
Kernel Version Linux 3.10.81 #4346 SMP Thu Jun 25 08:12:03 CEST 2015 armv7l
MAC Address E4:F4:C6:XX:XX:XX
Hostname
WAN Domain Name
LAN Domain Name
Current Time Wed, 01 Jul 2015 09:43:29
Uptime 3 min
CPU
CPU Model ARMv7 Processor rev 0 (v7l)
CPU Cores 2
CPU Clock 1200 MHz
Load Average 10% 0.25, 0.24, 0.11
CPU Temperature CPU 63.6 °C / WL0 48.43 °C / WL1 50.85 °C
* Guest wireless was flaky until after a reset and reconfigure. Getting guest wireless to work with dual radios broadcasting the same SSID on different channels is still very tricky though. Had to reset to defaults and manually set up the additional bride and dhcp for the guest network.
Router: R7000
Firmware: 27456
Status: Working
Reset: No
Errors: None
Previous: 27453
Firmware is stable however I have been playing with some wireless settings such as changing wifi channels and transmit power both on eth 2 which has caused some reboots when I apply the settings. Also the Wiviz survey does not appear to function properly. _________________ 2 R7800's (Kong OpenWRT 23.05) as access points
X86_64 build PC (DDWRT Build r55630)
3 R7000's (DDWRT build r53843)using one as a bridge currently
Netgear WNDR 3400 (DDWRT r55630)
Netgear DGND 3700 (with OpenWRT)