ECB-9500 / ECB-9750 console info

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Senao Devices
Author Message
brano
DD-WRT Novice


Joined: 12 Sep 2012
Posts: 1

PostPosted: Thu Sep 13, 2012 19:35    Post subject: ECB-9500 / ECB-9750 console info Reply with quote
The console is on the 6 pin connector, starting from front of the unit:
Pin 1: 3.3V
Pin 2: GND
Pin 3: Rx
Pin 4: Tx
Pin 5: ?
Pin 6: ?

Speed: 57600 8N1

Console log after boot with stock firmware 2.3.3
Code:

U-Boot 1.1.3 (Nov 20 2008 - 18:00:37)

Board: RT2880 DRAM:  32 MB
relocate_code Pointer at: 8bfa8000

 twe0 set to <NULL>

 toe0 set to <NULL>

 Default FLASH_CS1_CFG = 0511FFA1

 Ready Set Value = 0x0511FFA1

 Setup FLASH_CS1_CFG = 0511FFA1
 CAS 3 (D1835272)

 EN_ID_29LV640H, Size = 00800000 bytes

 Set info->start[0]=BC000000

AMD Read Mode, flash reset,triger at BC000000
flash_protect ON: from 0xBC400000 to 0xBC42522F
protect on 64
protect on 65
protect on 66

  monitor protection ON by default,monitor_flash_len = 152112

 ENV protection ON by default !!
flash_protect ON: from 0xBC430000 to 0xBC43FFFF
protect on 67
 D-CACHE set to 4 way
 I-CACHE set to 4 way

 ##### The CPU freq = 266 MHZ ####

 SDRAM bus set to 32 bit
 SDRAM size =32 Mbytes

Please choose the operation:
   1: Load system code to SDRAM via TFTP.
   2: Load system code then write to Flash via TFTP.
   3: Boot system code via Flash (default).
   4: Entr boot command line interface.
   5: Load ucos code to SDRAM via TFTP.
 2  1  0
   
3: System Boot system code via Flash.
## Booting image at bc450000 ...
   Image Name:   Linux Kernel Image
   Created:      2012-03-13   9:12:20 UTC

 System Control Status = 0x02910084
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1030357 Bytes = 1006.2 kB
   Load Address: 8a000000
   Entry Point:  8a196040
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8a196040) ...
## Giving linux memsize in MB, 32

Starting kernel ...


THIS IS ASIC - VERSION B
ramsize = 32 MBytes
rambase not set, set to default (0x08000000)
MEMORY DESCRIPTOR dump:
[0,8a275cc0]: base<0a000000> size<02000000> type<Free RAM memory>
PROC INIT OK!
init started: BusyBox v1.7.5 (2012-03-13 17:11:12 CST)
starting pid 10, tty '/dev/console': '/sbin/config_init'
Config Init version: 2.3.3.471 date: 2012/03/13
starting pid 55, tty '/dev/ttyS1': '/sbin/config_term'
************************************************************************
*                                  ECB9500                             *
************************************************************************

KernelApp/Ramdisk Ver:2.3.3.471          Date:2012/03/13
console>
Sponsor
powelljconnor
DD-WRT Novice


Joined: 09 May 2013
Posts: 1

PostPosted: Sat May 11, 2013 14:36    Post subject: Reply with quote
Where can I use this for?
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Senao Devices All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum