EOC1650 - Redboot banner but no prompt

Post new topic   Reply to topic    DD-WRT Forum Index -> Senao Devices
Author Message
westislander
DD-WRT Novice


Joined: 06 Oct 2012
Posts: 11

PostPosted: Fri May 03, 2013 1:38    Post subject: EOC1650 - Redboot banner but no prompt Reply with quote
I have an Engenius EOC1650 with the factory firmware 1.3.1 . I am attempting to connect to the console with telnet 192.168.1.1 9000 using a laptop on 192.168.1.10 .

I power up the device, then when the lan light comes on I can connect via telnet within the 2 seconds or so window. When I connect within the two second window I get the redboot banner.

*** Executing boot script in 1.980 seconds - enter ^C to abort.

So far so good. But when I type Control - C I get a "heart" on displayed back. I looked up the IBM PC code table and indeed it seems a small heart corresponds to hex 03 or "control-c" via the keyboard. The telnet session stays open for a few minutes but all that ever happens is that what I type is echoed back - No redboot messages, no prompt. After a few minutes the telnet session is terminated, and the EOC1650 seems to complete its boot process and the wireless interface comes up - and it works normally.

Is there some magic sequence I have to send after I connect with telnet besides just ctrl-c?

I'm using a Laptop with win xp pro for my telnet session, cabled from ethernet to the "lan" side of the POE adaptor, and the EOC1650 is connected to the POE side.

Is there something else I can try to get a redboot prompt?
Sponsor
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17619
Location: Hesse/Germany

PostPosted: Fri May 03, 2013 14:25    Post subject: Reply with quote
use the script for dir300vA
_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
westislander
DD-WRT Novice


Joined: 06 Oct 2012
Posts: 11

PostPosted: Sat May 04, 2013 16:55    Post subject: Reply with quote
So you suggest I use the script
( http://www.dd-wrt.com/routerdb/de/download.php?file=2048 ) for the D-Link Dir-300 rev a1, but use the image for the Engenius EOC1650?

The instructions for the DIR-300 rev A1 use a different IP address block - 192.168.20.80 - This address does not respond.


Can you give a little more detail on what you are suggesting?
westislander
DD-WRT Novice


Joined: 06 Oct 2012
Posts: 11

PostPosted: Sat Jul 20, 2013 12:25    Post subject: Reply with quote
I never got through redboot reprogramming, never got a prompt, and even with factory reset I could not login. Although I might have had the bad luck of having a one-off failure, (but it still works - unsecured only though) however I did not have success with this device.
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Senao Devices All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum