Posted: Sat Mar 23, 2013 21:09 Post subject: ASUS RT-N10 hw ver D1
Until now I successfully installed dd-wrt on rt-n10 c1. New shipment arrived and this time hw ver D1. Inside is BCM5356COKFBG with 4mb flash and 16 mb ram.
I tried many ddwrt images but no success. Any idea?
I managed to brick him with : "dd-wrt.v24-21223_NEWD-2_K2.6_mini_RT-N10.trx". it was unresponsive, and lights was at around 20% intensity. I managed to repair by programing serial flash 25Q32 using eeprom programmer.
Joined: 17 Apr 2009 Posts: 627 Location: Philadelphia, PA
Posted: Thu May 30, 2013 18:49 Post subject:
If you really want to get it supported quickly - send one of those 12 Rev D routers to Brainslayer - he'll get it working in no time! Otherwise, you'll need to wait until someone gathers the correct info from the router in order to have Brainslayer attempt to craete a build for it. But without the device in his hands, it makes it a lot harder to support (and more dangerous as in it could brick your router)... _________________ 1 x Linksys WRT160n v3
1 x Linksys WRT310n v1
1 x Linksys WRT600n v1.1
1 x Linksys WRT610n v1
1 x Linksys E2500
1 x Netgear WNDR3300
1 x Dlink DIR-825 v1
2 x Asus RT-AC66U
If you really want to get it supported quickly - send one of those 12 Rev D routers to Brainslayer - he'll get it working in no time! Otherwise, you'll need to wait until someone gathers the correct info from the router in order to have Brainslayer attempt to craete a build for it. But without the device in his hands, it makes it a lot harder to support (and more dangerous as in it could brick your router)...
What info is needed? I'll assist in any way I can, just let me know what I need to do, thanks!
Posted: Thu Jun 20, 2013 11:55 Post subject: Bricked RT-N10+ with K26 build 21223
I first tried to flash 21676 it booted fine in the webgui, But as I started configuring the router
1) pppoe username pass
2) ip of the router
3) dhcp pool
4) static dns
5) ntp time server
6) no-ip ddns service
7) under services I enabled ssh at 2222
8) telnet at 23
9) enabled log server and put in ip address
10) enabled vpn server ans put in ip and cleient ip range with chap secrets
the the moment I click APPLY... the webgui hangs and no response
ping to the router continues
then I hard reset the router back to 192.168.1.1
The webgui was accessable again followed the steps above upto point no:6 and clicked apply... again lost webgui acces
again HardReset the router tried to do firmware upgrade using k26_21676_ddwrt_mini.bin
again after upgrade lost access to webgui...
again Hardreset it and tried to flash k_26_21223_asusrtn10PLUSD1.trx after flash all the LED'S went very dimm (If I had read the forum I would not have flashed 21223
Posted: Fri Jun 21, 2013 17:30 Post subject: Re: Bricked RT-N10+ with K26 build 21223
cirkit wrote:
I first tried to flash 21676 it booted fine in the webgui, But as I started configuring the router
1) pppoe username pass
2) ip of the router
3) dhcp pool
4) static dns
5) ntp time server
6) no-ip ddns service
7) under services I enabled ssh at 2222
telnet at 23
9) enabled log server and put in ip address
10) enabled vpn server ans put in ip and cleient ip range with chap secrets
the the moment I click APPLY... the webgui hangs and no response
ping to the router continues
then I hard reset the router back to 192.168.1.1
The webgui was accessable again followed the steps above upto point no:6 and clicked apply... again lost webgui acces
again HardReset the router tried to do firmware upgrade using k26_21676_ddwrt_mini.bin
again after upgrade lost access to webgui...
again Hardreset it and tried to flash k_26_21223_asusrtn10PLUSD1.trx after flash all the LED'S went very dimm (If I had read the forum I would not have flashed 21223
no ping to router
router bricked
Please help
If You have access to eeprom programmer I'll send You bin file for serial flash and You can program it, as I did
Posted: Fri Jun 21, 2013 19:18 Post subject: Re: Bricked RT-N10+ with K26 build 21223
grunfov wrote:
cirkit wrote:
I first tried to flash 21676 it booted fine in the webgui, But as I started configuring the router
1) pppoe username pass
2) ip of the router
3) dhcp pool
4) static dns
5) ntp time server
6) no-ip ddns service
7) under services I enabled ssh at 2222
telnet at 23
9) enabled log server and put in ip address
10) enabled vpn server ans put in ip and cleient ip range with chap secrets
the the moment I click APPLY... the webgui hangs and no response
ping to the router continues
then I hard reset the router back to 192.168.1.1
The webgui was accessable again followed the steps above upto point no:6 and clicked apply... again lost webgui acces
again HardReset the router tried to do firmware upgrade using k26_21676_ddwrt_mini.bin
again after upgrade lost access to webgui...
again Hardreset it and tried to flash k_26_21223_asusrtn10PLUSD1.trx after flash all the LED'S went very dimm (If I had read the forum I would not have flashed 21223
no ping to router
router bricked
Please help
If You have access to eeprom programmer I'll send You bin file for serial flash and You can program it, as I did
Please send the file, I can manage the eeprom programmer I believe the ic is an 8 pin smd.
Not sure whether this info is useful. It was reported by some users in Taiwan that the following build works with RT-10+ D1 but the WAN port and LAN Port 4 is interchanged (i.e. LAN4 works as WAN port after flashing DDWRT). Some users also mentioned that PPPOE doesn't work.
telnet at 23
