nvram set httpd_enable=1
nvram set http_enable=1
nvram set remote_management=1
nvram set http_wanport=8080
nvram set httpsd_enable=1
nvram set https_enable=1
nvram set remote_mgt_https=1
nvram commit
reboot
After reboot and login again try web access with https format :https://My_router_ip:8080", even i try "https://My_router_ip" it didn't work out
Display in web browser The connection was interrupted
i scan my router port is open for 443 and 8080.
Any help please so i can set my webaccess with https.
Oh. forget to add
i did try flash with other version. still no luck _________________ [ATHEROS] TP-LINK TL-MR3220 v1 --> DD-WRT v3.0-r27506 (07/09/15) std - build 27506 (Brick )
[ATHEROS] TP-Link TL-WR1043ND v1.11 --> DD-WRT v3.0-r29059 std (02/09/16)
Joined: 03 Jan 2010 Posts: 7568 Location: YWG, Canada
Posted: Thu Jan 22, 2015 2:52 Post subject:
thats still not the latest from the ftp below, turn on https from gui theres no need to do it from ssh etc, thats only for disabling it to get access back, what browser are u using? it works fine for me on firefox 35 stable, 36 beta, 37 aurora & 38 nightly on windows 7 x64..also try restoring factory defaults/erasing nvram (dont restore from backup file)
there was previous problems before on some routers & browsers but those have been fixed _________________ LATEST FIRMWARE(S)
BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers
thats still not the latest from the ftp below, turn on https from gui theres no need to do it from ssh etc, thats only for disabling it to get access back, what browser are u using? it works fine for me on firefox 35 stable, 36 beta, 37 aurora & 38 nightly on windows 7 x64..also try restoring factory defaults/erasing nvram (dont restore from backup file)
there was previous problems before on some routers & browsers but those have been fixed
Update
uh... a little bit confuse here
setting by web in menu tab Administration then go
web Access menu see the Protocol there two option Http and HTTPS
i'm chose by check HTPPS in my understanding i'll be access the web login with https://my_router try boot then
i can't login to my router using "https://my_router"
So I change my way to setting my weblogin with cli
using telnet or ssh
i put command
nvram set http_lanport="443"
nvram commit; reboot
after boot
i try login with My_ip_router:443 uuuh it work.
check traffic is it really https .
Because my OS is trusty (ubuntu)so i use cli commmand
iftop
the result my connection to my_router is https .
All done
Question is why in web setting Protocol what is for ?
because in nvram show
if you click HTTPS in web setting protocol it will be
https_enable=1
but the other variable say :
http_lan_port=80 ----> will not change to HTTPS ( 443 )
hope someone can explain this 4 me
So here my conclusion;
1. to change weblogin to https use telnet or ssh and put command
nvram set http_lanport="443" ----> if want to HTTPS
nvram commit
reboot
or may be you can change you own port
2. if your web setting is down (can't be access) again use telnet or ssh command:
startservice httpd
Before please check is your httpd down or stuck
using
ps|grep httpd
when got the id kill it first then run again using
startservice httpd or you just type httpd after that go to webbrowser to access you router again .... by using your router ip address
default httpd port is 80 so just type your router ip you can access again you router
That's it 4 me good luck to try .... _________________ [ATHEROS] TP-LINK TL-MR3220 v1 --> DD-WRT v3.0-r27506 (07/09/15) std - build 27506 (Brick )
[ATHEROS] TP-Link TL-WR1043ND v1.11 --> DD-WRT v3.0-r29059 std (02/09/16)
I've never been able to access my router with HTTPS with any router or dd-wrt firmware. It should be just a simple check of the https box but it never has worked for me. All this stuff you guys are trying to do shouldn't be necessary.
I've never been able to access my router with HTTPS with any router or dd-wrt firmware. It should be just a simple check of the https box but it never has worked for me. All this stuff you guys are trying to do shouldn't be necessary.
HTTPS works on all of my routers from atheros,marvel,broadcom. It might be a problem on older units that do not have enough flash to include openssl, which is necessary nowadays, since browsers do not allow the use of old ciphers anymore. _________________ KONG PB's: http://www.desipro.de/ddwrt/
KONG Info: http://tips.desipro.de/
sig routers on those builds? if so u need to update them to the current build..thats why
Oh yes forget to say:
router mode : MR3220v1
i try using webaccess https with build r24461 did not success
when i try revert to facroty rom. get stuck. Because i use eth1 (port1 on my router )
i success revert using wifi. then i try build again with r25544 . bump still no luck
last i build my router using r25948. still no change
any suggest from me what build i can try tatsuya46
HTTPS is not supported anymore on this router, it only has 4MB flash and therefore comes with an old ssl lib. There is not enough flash to upgrade the ssl lib on these models. _________________ KONG PB's: http://www.desipro.de/ddwrt/
KONG Info: http://tips.desipro.de/
I've never been able to access my router with HTTPS with any router or dd-wrt firmware. It should be just a simple check of the https box but it never has worked for me. All this stuff you guys are trying to do shouldn't be necessary.
HTTPS works on all of my routers from atheros,marvel,broadcom. It might be a problem on older units that do not have enough flash to include openssl, which is necessary nowadays, since browsers do not allow the use of old ciphers anymore.
My router is a WRT1900ACS running DD-WRT v3.0-r30826. I can connect with HTTP but not HTTPS. I get this when I try to connect via HTTPS: This site can’t provide a secure connection.
I've never been able to access my router with HTTPS with any router or dd-wrt firmware. It should be just a simple check of the https box but it never has worked for me. All this stuff you guys are trying to do shouldn't be necessary.
HTTPS works on all of my routers from atheros,marvel,broadcom. It might be a problem on older units that do not have enough flash to include openssl, which is necessary nowadays, since browsers do not allow the use of old ciphers anymore.
My router is a WRT1900ACS running DD-WRT v3.0-r30826. I can connect with HTTP but not HTTPS. I get this when I try to connect via HTTPS: This site can’t provide a secure connection.
Your browser does not accept a connection. Not sure what browser you are using, but it obviously does not allow you to override their check. Try a different browser. _________________ KONG PB's: http://www.desipro.de/ddwrt/
KONG Info: http://tips.desipro.de/
Joined: 16 Nov 2015 Posts: 6436 Location: UK, London, just across the river..
Posted: Wed Nov 23, 2016 9:53 Post subject:
all browsers will deny access by default but you have to click on the right place... on Crome ADVANCED and then proceed, on Firefox ADVANCED and then add exception and so on .... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913