Posted: Sun Mar 01, 2015 10:27 Post subject: Netgear R7000 help...(Repeater Bridge)
Hello all,
im at my wits end here, I have setup repeater bridge so many times with Linksys and Belkin routers.
To make a long story short
After I flashed my R7000 to Brainslayer's most recent version (02/27/15), only the bridged version of my router works, but not the repeater...it keeps saying that my wireless devices cannot connect.
I have done 30-30-30 resets up the wazoo and used this guide below for setting up the repeater bridge:
Is there a special setting that needs to be enabled for the wireless repeater function to work?
again, just to reiterate, when i plug devices via Cat5 to the switch ports of the R7000, they connect fine but when I try to connect via wireless, it always fails (and never worked)
I tried Kongs latest firmware with the same result, so im beginning to think that its a setting that im missing...
Joined: 10 Jan 2015 Posts: 270 Location: Minnesota
Posted: Sun Mar 01, 2015 10:57 Post subject:
FWIW, 90 second hard resets dont work on arm-based routers like they did on any other platform. So reset by pressing the reset button, erasing nvram in the gui or (on some routers) holding the wps button on bootup.
I assume you looked at the broadcom section of the repeater bridge wiki? First, clear nvram on both units, dont use any backup configs, and configure both again.
If that still doesnt work, try a different build that is known to be solid (a recent version would be 26138, though airtime fairness is not enabled by default).
Assumptions:
1. Everyone on the forum has read the relevant forum section announcements.
2. For Broadcom section we have ALL at least tried to understand the "Peacock" thread,HERE
Assumptions:
1. Everyone on the forum has read the relevant forum section announcements.
2. For Broadcom section we have ALL at least tried to understand the "Peacock" thread,HERE
Posted: Mon Mar 02, 2015 7:12 Post subject: Re: THANK YOU !!!
Vastforce wrote:
Hey build 26138 WORKED !!!
Ive been up all night trying to get this piece of garbage to work, thank you so much !
Regards
just read this thread and i am using r7000 as repeater bridge also.. yeah the newer builds dont work properly in repeater bridge the client cant connect.. i am waiting for a fixed one too.. i am currently using kong 26285M it works good also but newest of kong is currently broken too..
do you experienct packet loss in your repeater bridge in r7000? _________________ WRT54GS v7 = 14929 micro repeater
e1500 = 19342 repeater mode
WRT54GS v1 = DD-WRT v24-sp2 (04/07/12) mega - build 18946M VINT Eko repeater mode
TPLINK - 1043ND v1.11 = 21223 client bridge
NETGEAR R7000 = 30880M Client Bridge
https://www.speedtest.net/my-result/d/beb94813-52a7-426d-b56b-d100a34364a3
Posted: Fri Apr 17, 2015 14:36 Post subject: Re: THANK YOU !!!
Razue wrote:
Vastforce wrote:
Hey build 26138 WORKED !!!
Ive been up all night trying to get this piece of garbage to work, thank you so much !
Regards
just read this thread and i am using r7000 as repeater bridge also.. yeah the newer builds dont work properly in repeater bridge the client cant connect.. i am waiting for a fixed one too.. i am currently using kong 26285M it works good also but newest of kong is currently broken too..
do you experience packet loss in your repeater bridge in r7000?
Hey Razue, I', having some issues with the repeater bridge function, you sig says that version 26339 works for Repeater Bridge, is that true?