Disregard previous post -- that all did happen, but I came back today and power was back to being pretty low on 2.4ghz. Too bad. Luckily I only have 3 2.4ghz devices, and they are pretty close to the AP. The 5ghz speed is excellent.
I have EA6200 with xvortex edited CFE - now my router pretends as EA6350 (EA6200 and EA6350 the same hardware)
No it is not the same hardware and EA6200 is not yet supported by dd-wrt.
EA6200 has the 5GHz radio as wl0 while EA6350 has the 2.4GHz radio as wl0.
Your radio variables will be for the wrong radio and that's why you get extremely bad throughput. _________________ Kernel panic: Aiee, killing interrupt handler!
I have EA6200 with xvortex edited CFE - now my router pretends as EA6350 (EA6200 and EA6350 the same hardware)
No it is not the same hardware and EA6200 is not yet supported by dd-wrt.
EA6200 has the 5GHz radio as wl0 while EA6350 has the 2.4GHz radio as wl0.
Your radio variables will be for the wrong radio and that's why you get extremely bad throughput.
This is a webflash.bin file. The major problem is DD-WRT did not release factory to dd-wrt.img. They might worry about Linksys will lock the highest classes of Router such as WRT1200 AC and any new model routers using broadcom chip etc.
Because linksys firmware filename usually is .img, Not .bin.
At the begin, I real flashed to dd-wrt successful but when I updated the last of webflash rom on 17 Mar 2016 and click updated buttion. The evil dream had happened.
The mini dd-wrt version 27770 cannot flash again when stock Linksys Firmware roll back.
It cannot restore to dd-wrt firmware so CFE file also cannot help me!
Finally, I had brought WRT1200AC and Archer C7. I also flash it. It is successful. The bugs are WRT1200AC had a bug about DNS searching. If pptp server can get the problem.
I hope that DD-WRT can release ArcherC5v2 and Linksys EA Series FACTORY TO DD-WRT.img
If dd-wrt plan to receive a fee about low grade router, it similar to buy app from play store If the price is below 10% of router price. I accept the fee.
M wrote:
This is a webflash.bin file. The major problem is DD-WRT did not release factory to dd-wrt.img. They might worry about Linksys will lock the highest classes of Router such as WRT1200 AC and any new model routers using broadcom chip etc.
Because linksys firmware filename usually is .img, Not .bin.
At the begin, I real flashed to dd-wrt successful but when I updated the last of webflash rom on 17 Mar 2016 and click updated buttion. The evil dream had happened.
The mini dd-wrt version 27770 cannot flash again when stock Linksys Firmware roll back.
It cannot restore to dd-wrt firmware so CFE file also cannot help me!
Finally, I had brought WRT1200AC and Archer C7. I also flash it. It is successful. The bugs are WRT1200AC had a bug about DNS searching. If pptp server can get the problem.
I hope that DD-WRT can release ArcherC5v2 and Linksys EA Series FACTORY TO DD-WRT.img
I have EA6200 with xvortex edited CFE - now my router pretends as EA6350 (EA6200 and EA6350 the same hardware)
No it is not the same hardware and EA6200 is not yet supported by dd-wrt.
EA6200 has the 5GHz radio as wl0 while EA6350 has the 2.4GHz radio as wl0.
Your radio variables will be for the wrong radio and that's why you get extremely bad throughput.
So with edited CFE will not fix that ?
If you have edit all nvram radio variables so they are correct for the EA6200 radios then it may work. _________________ Kernel panic: Aiee, killing interrupt handler!
If you have edit all nvram radio variables so they are correct for the EA6200 radios then it may work.
Yes i think all variables is set.
Here is dd-wrt screenshot:
Select a 2,4GHz channel, auto will not give you ht40!!
If you are using the Xvortex CFE I published with EA6350 radio parameters then there is only one edit you need to do for the swapped radios in EA6200, change the devpath variables:
devpath0=pci/2/1
devpath1=pci/1/1
That is much simpler than changing all 0: and 1: variables.
EA6200 is now supported for detection in dd-wrt but there will not be a separate build for it, it is included in the EA6350 build.
The only difference will be the routername displayed in the gui so if you want it detected as an EA6200 then you'll have to change 2 nvram variables in the xvortex CFE:
boardnum=20130125 (was 20140309 for EA6350)
boardrev=0x1100 (was 0x1200 for EA6350) _________________ Kernel panic: Aiee, killing interrupt handler!
Ok i read this thread many time and got every probleme write on it.
When i web flash the linksys-ea6400-numinit-super-hacky-smaller-version.bin from the web flash i got the error
Code:
VFS: Cannot open root device "mtdblock3" or unknown-block(31,3): error -19
When i flash the same bin from the serial link i got
Code:
Changed to the other image 0 (maxpartialboots exceeded)
If a force a boot (flash both nflash.trx) i got a kernel panic.
The only way i make a boot from a dd-wrt is from the lastest build of kong at the URL:http://desipro.de/ddwrt/K3-AC-Arm/
With this build everything work, webflash, serial flash, jtag flash.
At this point i'm relativly happy, but i want to flash the xvortex_ea6350, but if i try a mtd command i got a a message how said that the unlock ou write command is not support by /dev/mtd0 device.
I try to flash the lastest dd-wrt 04-05-2016-r29409, from the kong build, but after a first succesful boot (witch is no support mtd command neither) if i reboot it bootloop.
I begin to believe that my version of EA6350 is not compatible with the official build of dd-wrt.
Ok i read this thread many time and got every probleme write on it.
When i web flash the linksys-ea6400-numinit-super-hacky-smaller-version.bin from the web flash i got the error
Code:
VFS: Cannot open root device "mtdblock3" or unknown-block(31,3): error -19
When i flash the same bin from the serial link i got
Code:
Changed to the other image 0 (maxpartialboots exceeded)
If a force a boot (flash both nflash.trx) i got a kernel panic.
The only way i make a boot from a dd-wrt is from the lastest build of kong at the URL:http://desipro.de/ddwrt/K3-AC-Arm/
With this build everything work, webflash, serial flash, jtag flash.
At this point i'm relativly happy, but i want to flash the xvortex_ea6350, but if i try a mtd command i got a a message how said that the unlock ou write command is not support by /dev/mtd0 device.
I try to flash the lastest dd-wrt 04-05-2016-r29409, from the kong build, but after a first succesful boot (witch is no support mtd command neither) if i reboot it bootloop.
I begin to believe that my version of EA6350 is not compatible with the official build of dd-wrt.
Can you help me to understand what's going on.
Thanks in advence.
Hi!
With serial connection need flash two times:
nflash0.os
and
nflash1.trx
then reboot
And for xvortex CFE i did like this:
upload xvortex.bin CFE to router /tmp
then comand:
mtd erase mtd0
mtd write /tmp/xvortex.bin mtd0
When i erase mtd0 i get error but mtd0 was erased.
When I flash the mini(linksys-ea6400-numinit-super-hacky-smaller-version.bin) i get dd-wrt webGUI. Then when i flash the linksys-ea6350-webflash.bin over I don't know how but I get the linksys webGUI
Hi everyone, im new here.
I do this process and now im in middle of nowhere.
I Flash tha numinit mini firmware and after that i came back to linksys interface but now i cant make upgrade or anything.
The page ar in blank some times and others stay with the loading screen.
I Try:
1. 30/30/30 reset
2. TFTP from multiples tools and operating systems (Windows Ubuntu).
This router came to me yesterday and the first thig i do was this flas, so my wife wants to kill me, jajajaja.
Please help!!!
