New build is out 27944 (BS) V3.0 - Several Routers Bricked!

Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware
Goto page 1, 2, 3  Next
Author Message
kt_haddock
DD-WRT Guru


Joined: 25 Dec 2009
Posts: 710

PostPosted: Fri Oct 09, 2015 11:01    Post subject: New build is out 27944 (BS) V3.0 - Several Routers Bricked! Reply with quote
ftp://ftp.dd-wrt.com/betas/2015/10-09-2015-r27944/

Changelog: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=279467


This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 27944_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless.

If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.

_________________
[I prefer answere in whole sentence]
Sponsor
Bernadoe
DD-WRT User


Joined: 03 Dec 2014
Posts: 217

PostPosted: Fri Oct 09, 2015 14:43    Post subject: Reply with quote
Router: Netgear R7000
Firmware: DD-WRT v3.0-r27944 std (10/09/15)
Kernel: Linux 3.10.90 #4668 SMP Thu Oct 8 15:14:00 CEST 2015 armv7l
Status: Flashed back to dd-wrt.v24-27858
Reset: None
Errors: WiFi connects and then disconnects over and over. Flashed back to dd-wrt.v24-27858


Last edited by Bernadoe on Fri Oct 09, 2015 19:40; edited 2 times in total
PITABoy
DD-WRT User


Joined: 07 Jun 2006
Posts: 186

PostPosted: Fri Oct 09, 2015 15:43    Post subject: Reply with quote
I just flashed this on a Buffalo WZR-D1800H and my wireless is broken... I can connect to the router but not to the internet. It works fine with an ethernet cable.
I tried with and without a factory reset.
stalonge
DD-WRT Guru


Joined: 21 Jul 2006
Posts: 1898
Location: Fortaleza Ce Brazil

PostPosted: Fri Oct 09, 2015 16:18    Post subject: Reply with quote
my wzr1750dhp dont like this build .. its bricked ..


Confused Confused

_________________
DDwrt ...it rocks ....

1 R7800 54420 AP Wireguard webserver JFFS SAMBA FTP usb HD Mesh
1 R7800 54420 Cli Mesh
1 WZR1750 54389 AP Webserver Samba Wireguard
1 TP link Archer C7v5 54420 Cli Mesh
1 DD x86_64 48296 Gateway Samba Ftp Webserver
Hans Gruber
DD-WRT Novice


Joined: 17 Mar 2009
Posts: 25

PostPosted: Fri Oct 09, 2015 16:22    Post subject: Reply with quote
My D-Link DIR-868L rev. A didn't like it either. Had to use recovery to bring it back to life. Maybe a BCM4708 issue?
stevedensmore
DD-WRT Novice


Joined: 25 Oct 2010
Posts: 29

PostPosted: Fri Oct 09, 2015 16:28    Post subject: Reply with quote
10-09-2015-r27944 messed up my Netgear WNDR4500V2 that was running fine on 09-28-2015-r27858. The web interface wouldn't load after upgrading the firmware. I did a 30/30/30 and it still acts like it's functioning properly, but I still can't access the webgui or telnet into it. Pinging the router only results in timeout responses, even when I initially boot the router. Any ideas?

Last edited by stevedensmore on Fri Oct 09, 2015 20:33; edited 1 time in total
newdles
DD-WRT Novice


Joined: 27 Jan 2015
Posts: 2

PostPosted: Fri Oct 09, 2015 16:49    Post subject: Reply with quote
I just installed this on an ASUS RT-AC68U and it broke DHCP for my wireless clients. 30/30/30 did not fix it nor did a factory defaults fix it. DHCP was working fine on wired. I immediately reverted to r27858 which has been working without issue.
colnago
DD-WRT User


Joined: 23 Oct 2014
Posts: 98

PostPosted: Fri Oct 09, 2015 17:01    Post subject: Reply with quote
Router: Linksys EA6900
Firmware: DD-WRT v3.0-r27858
Kernel: DD-WRT 3.10.89 #4618 SMP
Status: Reverted to r27858
Reset: Yes
Errors: Router hang on boot. No wifi. No GUI connected with cat5 and a static IP. Ping response was TTL=100 at boot and then continuous timouts after ~a minute. Had to tftp back to previous release.
LinuxWalker
DD-WRT Novice


Joined: 03 Jan 2013
Posts: 4

PostPosted: Fri Oct 09, 2015 17:06    Post subject: Reply with quote
Yes I have two Wireless Bridges a Buffalo WZR-1750DHP and a Linksys e3200 both bricked...
KrypteX
DD-WRT Guru


Joined: 18 Jan 2014
Posts: 2411

PostPosted: Fri Oct 09, 2015 17:20    Post subject: Reply with quote
LinuxWalker wrote:
Yes I have two Wireless Bridges a Buffalo WZR-1750DHP and a Linksys e3200 both bricked...

I opened a ticket: http://svn.dd-wrt.com/ticket/4882

_________________
THERE ARE NO STRANGERS HERE; ONLY FRIENDS YOU HAVEN'T YET MET.
________________________________________________________________________________________________________
DD-WRT CHANGELOG | DEVICES | DD-WRT BUILDS | KONG BUILDS | UNOFFICIAL BUILDS | DD-WRT in VIRTUALBOX
Corsair1274
DD-WRT User


Joined: 08 Jul 2012
Posts: 53

PostPosted: Fri Oct 09, 2015 18:42    Post subject: :shock: Reply with quote
Could not flash my WZR1750DHP's with this build, but after reading these comments I will stay away. Why ruin a good thing that last build has been working beautiful.
slobodan
DD-WRT Guru


Joined: 03 Nov 2011
Posts: 1555
Location: Zwolle

PostPosted: Fri Oct 09, 2015 18:45    Post subject: Reply with quote
E4200 V1 flashed with dd-wrt.v24-27944_NEWD-2_K3.x_mega-e4200.bin (no reset). WiFi connects and then disconnects over and over. Flashed back to dd-wrt.v24-27858_NEWD-2_K3.x_mega-e4200.bin.
_________________
2 times APU2 Opnsense 21.1 with Sensei

2 times RT-AC56U running DD-WRT 45493 (one as Gateway, the other as AP, both bridged with LAN cable)

3 times Asus RT-N16 shelved

E4200 V1 running freshtomato 2020.8 (bridged with LAN cable)

3 times Linksys WRT610N V2 converted to E3000 and 1 original E3000 running freshtomato 2020.8 (bridged with LAN cable)


stevedensmore
DD-WRT Novice


Joined: 25 Oct 2010
Posts: 29

PostPosted: Fri Oct 09, 2015 20:12    Post subject: Reply with quote
Quick update: The webgui was finally accessible after 10+ minutes of being powered on. I quickly reverted back to the previous firmware, and all is well again.
quarantinemark
DD-WRT Novice


Joined: 09 Sep 2015
Posts: 3

PostPosted: Fri Oct 09, 2015 21:47    Post subject: Reply with quote
...

Last edited by quarantinemark on Mon Oct 12, 2015 14:35; edited 1 time in total
moppa
DD-WRT Novice


Joined: 14 Jul 2011
Posts: 26
Location: Northern Ireland

PostPosted: Sat Oct 10, 2015 10:34    Post subject: Reply with quote
Hardware: EA6300V1 (EA6400)

Have only upgaded one of my EA6300V1's. I upgraded from 27858. It took numerous reboots - it eventually seemed to reset itself to factory defaults on 27944.

This was no big deal as its only used as an AP - the 2nd one will be more painful as i use some startup commands for the WAN interface (Damn Sky UK!!)

Not brave enough to do the second one just yet!

_________________
Downstairs EA6300v1 - DD-WRT build 27858
Upstairs EA6300v1 - DD-WRT build 27858
Goto page 1, 2, 3  Next Display posts from previous:    Page 1 of 3
Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum