[GreyDoc]

DD-WRT build 29048 - 2016/02/05 has been released: ftp://ftp.dd-wrt.com/betas/2016/02-05-2016-r29048/

Changelog: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=279467

Your reports for Broadcom units are greatly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:

This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 29048_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.

[SoNic67]

Router: Linksys E4200
Firmware: DD-WRT v3.0-r29048 mega (02/05/16)
Kernel: Linux 3.10.96 #11399 Fri Feb 5 09:13:34 CET 2016 mips
Status: OK
Reset: Yes
Errors: No

LE1: Bridge crashed, I had to do a full reset to defaults to make it work again.
It is working for now.

LE2: I cannot make the VPN server to work - PPTP.

[Anti-Ultimate]

Router: Netgear R7000
Firmware: DD-WRT v3.0-r29048 std (02/05/16)
Kernel: Linux 4.4.1 #251 SMP Thu Feb 4 06:38:33 CET 2016 armv7l
Status: Working
Reset: No
Errors: No

EDIT: nvm, client bridge router crashed after 2 hours.

[chuks]

Router: TPLINK Archer C8
Firmware: DD-WRT v3.0-r29048 std (02/05/16)
Kernel: Linux 4.4.1 #253 SMP Fri Feb 5 05:38:17 CET 2016 armv7l
Status: Working
Reset: No
Errors: No

Internet and LAN LED Status light not working
2.4GHz and 5 GHz are OK

[Bernadoe]

Router: Netgear R7000
Firmware: DD-WRT v3.0-r29048 std (02/05/16)
Kernel: Linux 4.4.1 #251 SMP Thu Feb 4 06:38:33 CET 2016 armv7l
Status: Working
Reset: No
Previous: 29002
Errors: No

[zerophase]

Router: Asus RT-AC5300
Firmware: DD-WRT v3.0-r29048 std (02/05/16)
Kernel: Linux 4.4.1 #256 SMP Fri Feb 5 05:49:13 CET 2016 armv7l
Status: Connection seems more stable. (Speed test showed constant speed. Still need to test in network transfers)
Reset:
Errors: Ethernet ports are still non functional.

[arneande]

No Mobilbroadband back to DD-WRT v3.0-r28139 std (11/13/15
again, it is only me using that using mobilbroadband am think or?Yes am tried 10-15 builds after DD-WRT v3.0-r28139 std (11/13/15 they dont work and its not only Asus

arneande

[SinCalChewy]

Router: 2x Linksys e3000
Firmware: dd-wrt.v24-29048_NEWD-2_K3.x_mega-e3000.bin
Previous: dd-wrt.v24-29002_NEWD-2_K3.x_mega-e3000.bin
Kernel: Linux 3.10.96 #11399 Fri Feb 5 09:13:34 CET 2016 mips
Status: Working great as client bridges.
Reset: Yes
Errors: None thus far.

Edit: Speedtests on this build are noticeably slower than the previous build I was running. Just a quick note.
Edit: Still slightly slower, but my ISP was just being wack. It's ~10Mb/s slower, rolling back a build to 29002.

EDIT 3: After a PM from Jack82 about Airtime Fairness, I flashed this build again with a reset and it runs much smoother now, speed is back up again. So this build requires a reset to fully function with the Airtime Fairness setting having been changed. I have updated my info above.

[sierratango]

Router: D-Link 868L Rev A
Firmware: DD-WRT v3.0-r29048 std (02/05/16)
Kernel: Linux 4.4.1 #251 SMP Thu Feb 4 06:38:33 CET 2016 armv7l
Status: Working
Reset: No
Previous: 28647
Errors: No

Router: D-Link 880L
Firmware: DD-WRT v3.0-r29048 std (02/05/16)
Kernel: Linux 4.4.1 #251 SMP Thu Feb 4 06:38:33 CET 2016 armv7l
Status: Working
Reset: No
Previous: 28647
Errors: No

Multiple drives (ext4 and ntfs) are now mounting fine on both routers and are fully accessible, but under "Disk Info" there is always 1 missing drive that doesn't have Diskspace shown even though its mount information is displayed. Specifically, my 868L has 3 ext4 drives but 2 are shown. My 880L has 2 ntfs drives but 1 is shown.

Other than that, high CPU usage and boot loop issues seem completely resolved from my 868L.

Update: Uptime 2 days, 20:50 hours - no problems, both routers still running fine

Update 2: A few days later my 886L was reset due to power outage and then the issues resurfaced again (disk mount and high CPU usage). Going back to 28647. It seems Linux 4.4 is quite unstable.

[usharifu]

Router: D-Link DIR-895L
Firmware: DD-WRT v3.0-r29048 std (02/05/16)
Kernel: Linux 4.4.1 #256 SMP Fri Feb 5 05:49:13 CET 2016 armv7l
Status: Flashes OK
Reset: No
Errors: LAN/WAN ethernet ports are not functional



Router: D-Link DIR-890L
Firmware: DD-WRT v3.0-r29048 std (02/05/16)
Kernel: Linux 4.4.1 #256 SMP Fri Feb 5 05:49:13 CET 2016 armv7l
Status: Mostly OK
Reset: No
Errors:
- wl2 [5 GHz/802.11ac] will not accept WPA2 Personal (Mixed)--uses WEP and the WPA2 AES shared key is invalid
- Client Bridge mode on any wl(0-2) causes dd-wrt to be non-responsive (no web UI nor ping) and continual reboot; reset doesn't work, need to go into D-Link recovery mode and flash firmware

[mamock116]

Asus RT-AC56R so far so good. Ill report back later if I notice something wrong.

[CTEC]

Belkin F7D3301 / F7D7301 v1
DD-WRT v3.0-r29048 mega (02/05/16)
Linux 3.10.96 #11399 Fri Feb 5 09:13:34 CET 2016 mips
No Reset
Boots up and works.

[jaythree]

Router: Netgear R7000
Previous build: 12-10-2015-r28493\0

Firmware Version: DD-WRT v3.0-r29048 std (02/05/16)
Kernel Version: Linux 4.4.1 #251 SMP Thu Feb 4 06:38:33 CET 2016 armv7l
Status: Mostly working
Reset: Yes
Errors: USB storage doesn't work - when I plug in a USB mass storage device the router doesn't see it and nothing shows up in dmesg or /var/log/messages with syslogd enabled. Additionally no entry for the USB mass storage device is created in /dev/. I've tried disabling and reenabling USB storage support in the web UI and don't see anything in the router's logs when I do that, so I'm wondering if something may be broken with enabling USB storage. Here are my NVRAM values related to USB functions:

usb_automnt=1
usb_enable=1
usb_ip=0
usb_mntjffs=
usb_mntopt=
usb_mntpoint=mnt
usb_ohci=0
usb_printer=0
usb_runonmount=
usb_ses_umount=0
usb_storage=1
usb_uhci=0
usb_usb2=0

[jwh7]

Router: Netgear WNDR4000
Mode: Access Point
Firmware: DD-WRT v3.0-r29048 mega (02/05/16); k3x then k26
Kernel: (3.10.96 then...) Linux 2.6.24.111 #28619 Fri Feb 5 00:32:06 CET 2016 mips
Status: Ok on k2.6 so far
Reset: GUI and 'erase nvram' post-k3x update
Previous: 28942 k3x (with 2.4GHz radio disabled)
Errors: k3.10 build issues; 2.4 GHz and wired dropout

The k3x build seemed to work better than the past builds, but eventually still had issues (see above). Put k2.6 on, and been running several hours now with default advanced wireless settings.

[mwbuss8]

Router: Netgear ac1450
Firmware: DD-WRT v3.0-r29048 std (02/05/16)
Kernel: Linux 4.4.1 #251 SMP Thu Feb 4 06:38:33 CET 2016 armv7l
Status: OK
Reset: No
Errors: No
Not really an error, but when I have a swap partition mounted ram usage stays between 85-90% even with little activity. It just seems high for a router with 256mb ram. I just got the router, so I have no older builds for comparison. Its setup as an AP with samba, miniDLNA, and transmission. It still performs quite well for my purposes.