New Kong's build: DD-WRT 30465M - 2016/08/23

Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware
Goto page Previous  1, 2, 3, 4, 5, 6, 7, 8  Next
Author Message
mchaney
DD-WRT User


Joined: 26 Apr 2013
Posts: 389

PostPosted: Thu Aug 25, 2016 19:16    Post subject: Reply with quote
2 days, 8 hours here on R8500. Zero problems.

Thanks Kong!

Mike
Sponsor
techiesjc
DD-WRT Novice


Joined: 15 Feb 2015
Posts: 22
Location: San Jose, CA, USA

PostPosted: Fri Aug 26, 2016 0:25    Post subject: Reply with quote
Router: Netgear R8500
Firmware: 30465M
Kernel: Linux 4.4.19 #77 SMP Tue Aug 23 11:55:44 CEST 2016 armv7l
Status: Running as router 2 days all GOOD
Reset: Reboot - ddup (dirty)
Errors: None

DNSMasq as DHCP - 78 entries, 60 active - jffs lease store
LLTD
ttraff
DDNS
USB - jffs, opt, swap, local disk
NAS - 2 mounts
UPnP
CIFS - 1 mount

Router: Netgear R8500
Firmware: 30465M
Kernel: Linux 4.4.19 #77 SMP Tue Aug 23 11:55:44 CEST 2016 armv7l
Status: Running AP, one 5g radio off 2 days all GOOD
Reset: reboot - ddup (dirty)
Errors: None

Oh and speeds are great - wired and wireless are best I've had
egc
DD-WRT Guru


Joined: 18 Mar 2014
Posts: 12837
Location: Netherlands

PostPosted: Fri Aug 26, 2016 10:23    Post subject: Reply with quote
Router Name: EA6900

Router Model: Linksys EA6900 (XVortex CFE)

Firmware Version: DD-WRT v3.0-r30465M kongac (08/23/16)

Kernel Version: Linux 4.4.19 #77 SMP Tue Aug 23 11:55:44 CEST 2016 armv7l

Upgraded: from 30430M via telnet (upgrade via WebGui or DDUP not possible)

Reset: Yes, before and after (Erase NVRAM and WPS reset)

Configuration: AP, DHCP server, 2,4GHz wireless running, 5GHz disabled, some static leases and some port range forwarding, NVRAM size just below 32K (NVRAM size should not be a problem with the Xvortex CFE)

Status: Up and stable for 14 h, excellent wireless speed and range, WAN throughput 40/4 (is my ISP's maximum)
Errors: none so far , the syslog record from previous build: “wland : WLAN daemon successfully started” is gone.

Thanks Kong and BrainSlayer!!

_________________
Routers:Netgear R7000, R6400v1, R6400v2, EA6900 (XvortexCFE), E2000, E1200v1, WRT54GS v1.
Install guide R6400v2, R6700v3,XR300:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
Install guide R7800/XR500: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Forum Guide Lines (important read):https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324087
cc999
DD-WRT User


Joined: 20 Feb 2015
Posts: 110

PostPosted: Fri Aug 26, 2016 15:34    Post subject: R8500 Static Lease Bug Reply with quote
R-8500
Running for 3 days no problems, I then decided to assign my static IP leases in the services Tab like I have done dozens of times before. After setting up I saved, applied, then rebooted router and all clients. All clients could not connect to the router all said waiting for IP address. I then deleted all the assignments, applied and all clients connected no problem There seems to be a bug in the Static lease service.

CC
E-Man
DD-WRT User


Joined: 10 Mar 2014
Posts: 85

PostPosted: Fri Aug 26, 2016 17:33    Post subject: Re: R8500 Static Lease Bug Reply with quote
cc999 wrote:
R-8500
Running for 3 days no problems, I then decided to assign my static IP leases in the services Tab like I have done dozens of times before. After setting up I saved, applied, then rebooted router and all clients. All clients could not connect to the router all said waiting for IP address. I then deleted all the assignments, applied and all clients connected no problem There seems to be a bug in the Static lease service.

CC


Please try going to Status -> LAN, and delete the DHCP leases by pressing the Garbage Can icon. This may force the clients to request a new IP.

Hope this helps. Maybe you can help me with my issue!: Smile
http://www.dd-wrt.com/phpBB2/viewtopic.php?p=1044480
http://www.dd-wrt.com/phpBB2/viewtopic.php?p=1044441
mac913
DD-WRT Guru


Joined: 02 May 2008
Posts: 1848
Location: Canada

PostPosted: Fri Aug 26, 2016 17:47    Post subject: Re: R8500 Static Lease Bug Reply with quote
cc999 wrote:
R-8500
Running for 3 days no problems, I then decided to assign my static IP leases in the services Tab like I have done dozens of times before. After setting up I saved, applied, then rebooted router and all clients. All clients could not connect to the router all said waiting for IP address. I then deleted all the assignments, applied and all clients connected no problem There seems to be a bug in the Static lease service.

CC


I have static leases enabled without any issues on my R7000 WAN Router.

UpTime: 2d-9h (WAN) & 2d-17h (WiFi)

_________________
Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9

Off Site 1

R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4

Off Site 2

R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531


YAMon 3.4.6 | DNSCrypt-Proxy V2
stalonge
DD-WRT Guru


Joined: 21 Jul 2006
Posts: 1898
Location: Fortaleza Ce Brazil

PostPosted: Fri Aug 26, 2016 18:14    Post subject: Re: R8500 Static Lease Bug Reply with quote
mac913 wrote:
cc999 wrote:
R-8500
Running for 3 days no problems, I then decided to assign my static IP leases in the services Tab like I have done dozens of times before. After setting up I saved, applied, then rebooted router and all clients. All clients could not connect to the router all said waiting for IP address. I then deleted all the assignments, applied and all clients connected no problem There seems to be a bug in the Static lease service.

CC


I have static leases enabled without any issues on my R7000 WAN Router.

UpTime: 2d-9h (WAN) & 2d-17h (WiFi)



%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%

R8500 & R7000 both more than 3 days working


I have 12 static leases too .. its working ..


I had same issue , but after you set your static leases .. press apply and turn power off and on ... the clients will connect again ..


Very Happy Very Happy

_________________
DDwrt ...it rocks ....

1 R7800 54420 AP Wireguard webserver JFFS SAMBA FTP usb HD Mesh
1 R7800 54420 Cli Mesh
1 WZR1750 54389 AP Webserver Samba Wireguard
1 TP link Archer C7v5 54420 Cli Mesh
1 DD x86_64 48296 Gateway Samba Ftp Webserver
ramfast
DD-WRT Novice


Joined: 25 Nov 2014
Posts: 13

PostPosted: Fri Aug 26, 2016 19:57    Post subject: Reply with quote
Router: Asus RT-AC68U
Firmware: DD-WRT v3.0-r30465M kongac (08/23/16)
Kernel: Linux 4.4.19 #77
Status: OK
Reset: NO
Errors: NO

Observation : led for Wifi 5 GHz not working

BR
SuperSaiyajin
DD-WRT Novice


Joined: 08 Apr 2013
Posts: 38

PostPosted: Fri Aug 26, 2016 20:25    Post subject: Reply with quote
Router:Dlink-DIR860L-A1
Firmware: DD-WRT v3.0-r30465M kongac (08/23/16)
Kernel:Linux 4.4.19 #77 SMP Tue Aug 23 11:55:44 CEST 2016 armv7l
Status:Ok
Reset:Yes via WebGui
Errors:
2.4ghz and 5ghz MACadd is the same, is this normal for DDWRT?
Just notice this because my son new phone which is connected to 5ghz channel always disconnects then connect then disconnects almost every second.
by changing the MAC of 2.4ghz just to make it different fix the problem.

I tried flashing the default firmware and it shows different Macs for each band.

Thank you Sir Kong and BS for your Hardwork

_________________
Dlink-DIR860L-A1
DD-WRT v3.0-r30560M kongac (09/05/16)
mac913
DD-WRT Guru


Joined: 02 May 2008
Posts: 1848
Location: Canada

PostPosted: Fri Aug 26, 2016 22:45    Post subject: Reply with quote
SuperSaiyajin wrote:
Router:Dlink-DIR860L-A1
Firmware: DD-WRT v3.0-r30465M kongac (08/23/16)
Kernel:Linux 4.4.19 #77 SMP Tue Aug 23 11:55:44 CEST 2016 armv7l
Status:Ok
Reset:Yes via WebGui
Errors:
2.4ghz and 5ghz MACadd is the same, is this normal for DDWRT?
Just notice this because my son new phone which is connected to 5ghz channel always disconnects then connect then disconnects almost every second.
by changing the MAC of 2.4ghz just to make it different fix the problem.

I tried flashing the default firmware and it shows different Macs for each band.

Thank you Sir Kong and BS for your Hardwork


All 8 SSIDs have different MACs on my R7000 WiFi Router....

Physical Interface wl0 - SSID [ssid1] HWAddr [E4:xx:xx:xx:xx:26]
Virtual Interfaces wl0.1 SSID [ssid2] HWAddr [E6:xx:xx:xx:xx:27]
Virtual Interfaces wl0.2 SSID [ssid3] HWAddr [E6:xx:xx:xx:xx:29]
Virtual Interfaces wl0.3 SSID [ssid4] HWAddr [E6:xx:xx:xx:xx:2C]
Physical Interface wl1 - SSID [ssid5] HWAddr [E4:xx:xx:xx:xx:27]
Virtual Interfaces wl1.1 SSID [ssid6] HWAddr [E6:xx:xx:xx:xx:28]
Virtual Interfaces wl1.2 SSID [ssid7] HWAddr [E6:xx:xx:xx:xx:2A]
Virtual Interfaces wl1.3 SSID [ssid8] HWAddr [E6:xx:xx:xx:xx:2F]

_________________
Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9

Off Site 1

R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4

Off Site 2

R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531


YAMon 3.4.6 | DNSCrypt-Proxy V2
labo
DD-WRT Guru


Joined: 30 Jan 2015
Posts: 676
Location: Texas, USA

PostPosted: Fri Aug 26, 2016 22:51    Post subject: Finally off from 29300 build Reply with quote
Updated R8000, R7000, RT-AC68. Up without any issues 2+ days and counting.
This is the first time that passed beyond 2days without any issues ever since the build 29300(main router crossed 100+ days).
R8000 was worst affected router with all the firmware builds: > 29300 < 30465
I have been patiently waiting for this.

Thanks Kong!
glassbase
DD-WRT Novice


Joined: 14 Aug 2016
Posts: 3

PostPosted: Fri Aug 26, 2016 23:03    Post subject: Reply with quote
Router: EA6400
Firmware: DD-WRT v3.0-r30465M kongac (08/23/16)
Kernel: Linux 4.4.19 #77 SMP Tue Aug 23 11:55:44 CEST 2016 armv7l
Status: Good
Reset: No
Errors: None
Updated via telnet from 8/16/16 release

DHCP running, DNSMasq running, 8 static leases, 2.4GHz 40MHly N-ony and 5GHZ 80Mhz AC-only, both with WPA2 AES

Nothing but stability and improvements over the last few Kong release - thx Kong

Signal strength and RX/TX rates from my many wireless devices seem a big higher from last release at quick glance.

PS - my first post as well - been using DDWRT for years, but thought I should join the community too. Cheers
mgm
DD-WRT User


Joined: 27 Dec 2013
Posts: 69

PostPosted: Sat Aug 27, 2016 10:03    Post subject: Reply with quote
Router: R7000
Firmware: DD-WRT v3.0-r30465M kongac (08/23/16)
Kernel: Linux 4.4.19 #77 SMP Tue Aug 23 11:55:44 CEST 2016 armv7l
Status: Working
Reset: erase nvram before an after flash Firmware and configure all settings new

No errors for 48 hours.. thx KONG for great work....use an ovpn Client with settings in the "Commands" Tab work perfect Smile

CPU temp. about 55-60 degrees
egc
DD-WRT Guru


Joined: 18 Mar 2014
Posts: 12837
Location: Netherlands

PostPosted: Sat Aug 27, 2016 10:15    Post subject: Reply with quote
Linksys EA 6900 (XvortexCFE) has the same problem
But after resetting with WPS button (but not from GUI or from erase nvram), I have the correct MAC addresses.
I do not know if you can reset with the WPS button (press WPS button, unplug, wait 10 sec, restore power and wait 25-30 seconds (on linksys the router starts flashing after approx 25 sec)), but it is worth a try

SuperSaiyajin wrote:
Router:Dlink-DIR860L-A1
Firmware: DD-WRT v3.0-r30465M kongac (08/23/16)
Kernel:Linux 4.4.19 #77 SMP Tue Aug 23 11:55:44 CEST 2016 armv7l
Status:Ok
Reset:Yes via WebGui
Errors:
2.4ghz and 5ghz MACadd is the same, is this normal for DDWRT?
Just notice this because my son new phone which is connected to 5ghz channel always disconnects then connect then disconnects almost every second.
by changing the MAC of 2.4ghz just to make it different fix the problem.

I tried flashing the default firmware and it shows different Macs for each band.

Thank you Sir Kong and BS for your Hardwork

_________________
Routers:Netgear R7000, R6400v1, R6400v2, EA6900 (XvortexCFE), E2000, E1200v1, WRT54GS v1.
Install guide R6400v2, R6700v3,XR300:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
Install guide R7800/XR500: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Forum Guide Lines (important read):https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324087
cc999
DD-WRT User


Joined: 20 Feb 2015
Posts: 110

PostPosted: Sat Aug 27, 2016 10:57    Post subject: Re: R8500 Static Lease Bug Reply with quote
stalonge wrote:
mac913 wrote:
cc999 wrote:
R-8500
Running for 3 days no problems, I then decided to assign my static IP leases in the services Tab like I have done dozens of times before. After setting up I saved, applied, then rebooted router and all clients. All clients could not connect to the router all said waiting for IP address. I then deleted all the assignments, applied and all clients connected no problem There seems to be a bug in the Static lease service.

CC


I have static leases enabled without any issues on my R7000 WAN Router.

UpTime: 2d-9h (WAN) & 2d-17h (WiFi)



%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%

R8500 & R7000 both more than 3 days working


I have 12 static leases too .. its working ..


I had same issue , but after you set your static leases .. press apply and turn power off and on ... the clients will connect again ..


Very Happy Very Happy


I tried this and it did not work! Really weird. I am certainly not a nubie to all of this and I tried everything. Even dropped to an earlier firmware and same result. The clients never seem to find an ip from the router. I went back to stock and everything works again (static ip).

I factory rest thrru the GUI and also the reset button. I even did a 30-30-30 before and after the flash. Same result.

One thing that does not work is the nvram telnet command but the other methods essentially do the same thing.

Now on stock any suggestions, this is so disappointing.

CC
Goto page Previous  1, 2, 3, 4, 5, 6, 7, 8  Next Display posts from previous:    Page 3 of 8
Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum