Changelog
https://www.dd-wrt.com/phpBB2/viewtopic.php?t=279467
This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 30432_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless.
If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.
E2500v1
DD-WRT v3.0-r30471 mega (08/24/16)
Linux 3.10.102 #13988 Wed Aug 24 17:04:42 CEST 2016 mips
[dd-wrt.v24-30471_NEWD-2_K3.x_mega.bin]
previous
30432 - Linux 3.10.102 #13856 Tue Aug 16 15:09:13 CEST 2016 mips
GUI install - No Reset
Used as WAP only
HT40
all good
uptime 1:56
Model: Netgear WNDR4500v2
Firmware: DD-WRT v3.0-r30471 giga (08/24/16)
Kernel: Linux 3.10.102 #13968 Wed Aug 24 16:35:27 CEST 2016 mips
Uptime/Mode/Previous: 15min / AP / 30432
Status: No reset; I last did one with 30082.
The previous firmware was up over 8 days without dropping the 2.4 GHz radio, which confirms having a VAP setup (regardless of it working) fixes that previously common problem. MoreBloodWine indicated a reboot fixes the VAP/Guest network, and I recall mrjcd mentioning it for other routers, but I haven't tried that yet. _________________ #NAT/SFE/CTF: limited speed w/ DD#Repeater issues#DD-WRT info: FAQ, Builds, Types, Modes, Changes, Demo#
OPNsense x64 5050e ITX|DD: DIR-810L, 2*EA6900@1GHz, R6300v1, RT-N66U@663, WNDR4000@533, E1500@353,
WRT54G{Lv1.1,Sv6}@250|FreshTomato: F7D8302@532|OpenWRT: F9K1119v1, RT-ACRH13, R6220, WNDR3700v4
Posted: Thu Aug 25, 2016 9:08 Post subject: Netgear WNDR4000
Router: Netgear WNDR4000
Firmware:dd-wrt.v24-30471_NEWD-2_K3.x_mega-nv64k.bin (7 947 264 +0 bytes)
Previous: dd-wrt.v24-30432_NEWD-2_K3.x_mega-nv64k
Kernel: Linux 3.10.102 #13984 Wed Aug 24 16:59:30
Temp/Load: WL0 52.8 °C / WL1 48.7 °C / 0.05, 0.05, 0.02 (4%)
Reset: Nope, I like it dirty.
Errors/Issues: Not yet. (Uptime 7min)
Testing speeds on 12/1Mbit/s ADSL (using local linux box):
Quote:
smask@LGx4:~$ speedtest
Retrieving speedtest.net configuration...
Retrieving speedtest.net server list...
Testing from Net at Once (Redacted IP)...
Selecting best server based on latency...
Hosted by Mediateknik (Varberg) [50.67 km]: 33.155 ms
Testing download speed........................................
Download: 13.53 Mbit/s
Testing upload speed..................................................
Upload: 1.64 Mbit/s
_________________
R6800 BS K4.4 r46329 (Main router)
WNDR3700v3 r40009 (WAP)
--- Spares ---
R7500 Stock FW (Found it at the city dump alongside a EX7000)
WNDR4300 BS K3.18 r40559 (Flaky ethernet ports)
R7000 BS K4.4 r40750 (Dead ethernet ports, cooked to death in the attic a really hot summers day, about 105-110C)
WNDR4000 BS K3.10 r31899 (Loaned out to tenant who lives in my old home)
WNR2000v2 BS K2.6 r39230 (bricks and giggles)
+ A bunch of WRT54GL:s
I use my routers with pretty basic configuration. Only having WiFi + BT coexist enabled.
I don't have any USB devices connected.
Router: Netgear R7000
Firmware: DD-WRT v3.0-r30471 std (08/24/16)
Previous: DD-WRT v3.0-r30356 std (08/04/16)
Kernel: Linux 4.4.19 #1296 SMP Wed Aug 24 09:56:33 CEST 2016 armv7
Temp/Load: CPU 62.5 °C / WL0 52.3 °C / WL1 53.3 °C
0.05, 0.03, 0.00
Reset: Nope, I like it dirty.
Errors/Issues: Not yet. (Uptime 1 hour+)
OpenVPN working fine. Seems issue with ebtables is fixed as well.
Router: Netgear R7000
Firmware: DD-WRT v3.0-r30471 std (08/24/16)
Kernel: Linux 4.4.19 #1296 SMP Wed Aug 24 09:56:33 CEST 2016 armv7l
Status: Working
Reset: No
Previous: 30432
Errors: No
CPU Temperature : CPU 56.9 °C / WL0 46.8 °C / WL1 50.9 °C
Posted: Thu Aug 25, 2016 14:40 Post subject: Initially OK but now not so sure
Router Model Netgear R7000
Firmware Version DD-WRT v3.0-r30471 std (08/24/16)
Previous: Kong's 30430
Kernel Version Linux 4.4.19 #1296 SMP Wed Aug 24 09:56:33 CEST 2016 armv7l
Load Average 13% 0.48, 0.23, 0.09
CPU Temperature CPU 58.0 °C / WL0 45.9 °C
Reset: Not initially, but the internet disconnected even though the lights were flashing up a storm, so I power-cycled the router. This happened about 15 min after initial loading of the firmware. I did not do a NVRAM reset nor a router reset initially. Probably should have done at least the reset.
Errors/Issues: See Reset.
Speedtest: Seems to be OK, but looks like Comcast lowered my max rate to 20Mb download, initially was 30.
Oops, as I was writing this, and about 15 min after the initial reset, the router UI locked up, even though it was still happily flashing its lights. I was able to navigate to a separate website, so it was still acting as a router. Maybe that was a fluke from the reset. But if it happens again, I'm going back to a previous version.
It seems my D-Link DIR-880L is broken now. I'm not near the device, so I can not check why right now.
Update: after a factory reset everything works fine.
Last edited by onnoossendrijver on Thu Aug 25, 2016 18:27; edited 1 time in total
Posted: Thu Aug 25, 2016 15:29 Post subject: Hung Again
Seems like clockwork, after another 15 min or so, the UI on 30471 on my R7000 hung again, so I jumped ship and went with Kong's 30465. In any case, I do appreciate the hard work Brainslayer performs on these versions of dd-wrt. Thanks much.
Posted: Thu Aug 25, 2016 15:50 Post subject: Re: Hung Again
TonyK1321 wrote:
Seems like clockwork, after another 15 min or so, the UI on 30471 on my R7000 hung again, so I jumped ship and went with Kong's 30465. In any case, I do appreciate the hard work Brainslayer performs on these versions of dd-wrt. Thanks much.
Why going back if you haven't even done an erase nvram?
Despite that, there is a boot loop fix in 65 that is not present yet in 71.
Posted: Fri Aug 26, 2016 1:29 Post subject: Asus RT-AC68U
Router: Asus RT-AC68U
Firmware: DD-WRT v3.0-r30471 std (08/24/16)
Previous: DD-WRT v3.0-r30432 std (08/16/16)
Kernel: Linux 4.4.19 #1296 SMP Wed Aug 24 09:56:33 CEST 2016 armv7l
Previous: Linux 4.4.17 #1265 SMP Mon Aug 15 06:25:47 CEST 2016 armv7l
Status: ok
Reset: no
Errors: no
Operating Mode: Gateway
Uptime: 11:42
Temperature: CPU 79.1 °C / WL0 49.1 °C / WL1 51.8 °C
