This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 30771_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless.
If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build. _________________ [I prefer answere in whole sentence]
Router: Linksys E3000 (formerly WRT610N V2)
Firmware: dd-wrt.v24-30771_NEWD-2_K3.x_mega-e3000.bin
Kernel: 3.10.103
Reset: no
Errors: no.
Note: use it as switch and AP. _________________ 2 times APU2 Opnsense 21.1 with Sensei
2 times RT-AC56U running DD-WRT 45493 (one as Gateway, the other as AP, both bridged with LAN cable)
3 times Asus RT-N16 shelved
E4200 V1 running freshtomato 2020.8 (bridged with LAN cable)
3 times Linksys WRT610N V2 converted to E3000 and 1 original E3000 running freshtomato 2020.8 (bridged with LAN cable)
Router: Linksys E4200
Firmware: dd-wrt.v24-30771_NEWD-2_K3.x_mega-e3000.bin
Kernel: 3.10.103
Reset: no
Errors: no.
Note: use it as switch and AP. _________________ 2 times APU2 Opnsense 21.1 with Sensei
2 times RT-AC56U running DD-WRT 45493 (one as Gateway, the other as AP, both bridged with LAN cable)
3 times Asus RT-N16 shelved
E4200 V1 running freshtomato 2020.8 (bridged with LAN cable)
3 times Linksys WRT610N V2 converted to E3000 and 1 original E3000 running freshtomato 2020.8 (bridged with LAN cable)
Router: ASUS RT-N12 D1
Firmware: DD-WRT v3.0-r30771 mega (10/18/16)
Kernel: Linux 3.10.103 #14601 Tue Oct 18 12:31:14 CEST 2016 mips
Status: Working
Reset: no / Rebooting only
Errors: no
Note: use it as switch and AP.
No problems, but the GUI is a bit slower than the previous one.
Router: Buffalo WZR-1750DHP & DHPD
Firmware: DD-WRT v3.0-r30771 std (10/18/16)
Kernel: Linux 4.4.25 #1507 SMP Mon Oct 17 09:32:52 CEST 2016 armv7l
Reset: Yes, via web GUI reset to factory defaults
Errors: none
UpTime: 8h:44min
Previous: r30731
Still the both routers locks up the LAN when i add any interface to the QoS interface priority. Queueing Discipline PIE still cuts the bandwidth in half when implemented.
Would it be possible to allow for longer program names in the port forwarding entry fields if a ticket is made?
Note:
Both routers are CPU overclocked to 1200mhz.
Router: R7000
Firmware: r30771
Previous: r30709
Kernel: Linux 4.4.25 #1507 SMP Mon Oct 17 09:32:52 CEST 2016 armv7l
Status: Working. R7000 is the main router + OpenVPN Server
Reset: No, dirty flash from previous release
Errors: None so far with uptime of 1 hour and 25 minutes
Router : Netgear R7000
Firmware: DD-WRT v3.0-r30771 std (10/18/16)
Kernel: Linux 4.4.25 #1507 SMP Mon Oct 17 09:32:52 CEST 2016 armv7l
Status: Working
Reset: No
Previous: 30731
Errors: No
Router : EA6400
Firmware: DD-WRT v3.0-r30771 std (10/18/16)
Kernel: Linux 4.4.25 #1507 SMP Mon Oct 17 09:32:52 CEST 2016 armv7l
Status: Working
Reset: No
Previous: 30709
Errors: No
Router : WRT54GL V1.1
Firmware: dd-wrt.v24_mini_wrt54g.bin broadcom (10/18/16)
Kernel: ?
Status: Bricked router
Reset: No
Previous: 30731
Errors: Yes, after flashing no web interface. After reset router unresponsive, flashing power led only.
Managed to recover using tftp to standard linksys fw and then back to r30731.
Usually have no problems at all. Maybe a one off.
Posted: Thu Oct 20, 2016 10:00 Post subject: Asus RT-AC68U & 2 Linksys E2000
Asus RT-AC68U
Firmware: DD-WRT v3.0-r30771 std (10/18/16) (previous r30731)
Kernel: Linux 4.4.25 #1507 SMP Mon Oct 17 09:32:52 CEST 2016 armv7l
2.4Ghz (NG-mixed) with 40Mhz channel width: Ok
5Ghz (Mixed) with 80Mhz channel width: Ok
SSH: Ok
Telnet: Disabled but tested to work
USB 2.0 storage ext3 mount to JFFS: Ok
USB 3.0 storage EXT3 mount to /mnt: Ok
Samba shared drive: Ok
Site Survey: Ok
Wi-viz Survey 2.4Ghz & 5Ghz: Ok
Reset: Yes
Status: Ok
Uptime: 31 minutes
CPU Temperature: CPU 86.4 °C / WL0 56.5 °C / WL1 54.3 °C
2 x E2000
DD-WRT v3.0-r30771 mega (10/18/16) (previous r30731)
Kernel: Linux 3.10.103 #14597 Tue Oct 18 12:27:10 CEST 2016 mips
2.4Ghz (NG-mixed) with 40Mhz channel width: Ok
SSH: Ok
Telnet: Disabled but tested to work
Site Survey: Ok
Wi-viz Survey 2.4Ghz: Ok
Reset: No
Status: Ok
Uptime: 12 hours
CPU Temperature: WL0 53.3 °C
Annoyances: HTTPS broken
All devices working as AP's each with individual 1Gb wired connections to main firewall
Would like to see the defaults changed from Telnet --> SSH and HTTP --> HTTPS in this day and age
Router: TrendNet TEW-811DRU
Firmware Version
DD-WRT v3.0-r30771 mini (10/18/16)
Kernel Version
Linux 4.4.25 #1510 Tue Oct 18 07:47:06 CEST 2016 armv7l Status: Not Working
Reset: No
Previous: r29396
Errors: USB Drive will not mount. Status is noted as Not Mounted.
I went back to r29396. This is the last version that will allow usb drives for this model and I need this for YAMon3. This is reported in ticket 5467.
http://svn.dd-wrt.com/ticket/5467 _________________ Netgear R8000 - r50814 std - Main Router
Asus RT-AC68R -r46329 std - AP
Asus RT-AC68R -r46329 std - AP
TEW811DRU -r50595 mini - AP
TEW811DRU -r50595 mini - AP
Router: Asus RT-AC56U
Firmware Version: DD-WRT v3.0-r30771 std (10/18/16)
Kernel: Linux 4.4.25 #1507 SMP Mon Oct 17 09:32:52 CEST 2016 armv7l
Reset: Yes
Errors: None
My internet speed is 200/10 tier from my ISP and I set up QoS to get A grades on all test's on DSLReports speed and bufferbloat test while having slightly faster than advertised speeds with firmware 30709 and older firmware. With firmware 30771 and 30731, download speed is down on average 20% compared to 30709 and has been like that consistently for the last week.
Router: Linksys E2000
Firmware Version: DD-WRT v3.0-r30771 mini (10/18/16)
Kernel: Linux 2.6.24.111 #31408 Tue Oct 18 01:15:43 CEST 2016 mips
Reset: yes
Errors: the wan port seems to have dropped from 10/1000 to 10/100 - can't figure out why. (note: I have assign WAN Port to Switch enabled, this is not my main router) _________________ All we wanna do is eat your brains.
Netgear WNDR3700v3
Linksys e2000
Router: Linksys EA6300v.1/EA6400
Firmware: v3.0-r30771 std (10/18/16)
Previous: v3.0-r30731 std (10/06/16))
Kernel: Linux 4.4.25 #1507 SMP Mon Oct 17 09:32:52 CEST 2016 armv7l
Status: Working
Reset: No
Errors: Same MAC for both radio (2.4/5Ghz), gpio 8 not working.
Uptime :11:58
In use as AP (2.4 Ghz bridged) and Repeater Bridge (5Ghz bridged)
Samba Enabled - Running (2TB NTFS, 12MB/s writing at 5GHz)
CPU ModelBroadcom BCM4708
CPU Cores2
CPU Clock1200 MHz
CPU Temperature CPU 66.4 °C / WL0 46.2 °C / WL1 55.4 °C
Flashing on WebGui doesnt work.
Flashed using PuTTY to Telnet.
Code:
cd /tmp/root
mtd -f write linksys-ea6400-webflash.bin linux2
mtd -f write linksys-ea6400-webflash.bin linux
reboot
