Joined: 18 Mar 2014 Posts: 12917 Location: Netherlands
Posted: Fri Oct 21, 2016 15:37 Post subject:
mandepsi wrote:
Router: Linksys EA6300v.1/EA6400
Firmware: v3.0-r30771 std (10/18/16)
Previous: v3.0-r30731 std (10/06/16))
Kernel: Linux 4.4.25 #1507 SMP Mon Oct 17 09:32:52 CEST 2016 armv7l
Status: Working
Reset: No
Errors: Same MAC for both radio (2.4/5Ghz), gpio 8 not working.
Uptime :11:58
In use as AP (2.4 Ghz bridged) and Repeater Bridge (5Ghz bridged)
Samba Enabled - Running (2TB NTFS, 12MB/s writing at 5GHz)
CPU ModelBroadcom BCM4708
CPU Cores2
CPU Clock1200 MHz
CPU Temperature CPU 66.4 °C / WL0 46.2 °C / WL1 55.4 °C
Flashing on WebGui doesnt work.
Flashed using PuTTY to Telnet.
Code:
cd /tmp/root
mtd -f write linksys-ea6400-webflash.bin linux2
mtd -f write linksys-ea6400-webflash.bin linux
reboot
For the linksys EA6900 with Xvortex CFE, the MAC addresses are only properly initialized if you reset with WPS button (hold WPS button, unplug, wait 10 seconds, replug and wait approx. 25 seconds until linksys light flashes)
Resetting by GUI or erase nvram gets the same MAC addresses for both wireless. Maybe this can help you also _________________ Routers:Netgear R7000, R6400v1, R6400v2, EA6900 (XvortexCFE), E2000, E1200v1, WRT54GS v1.
Install guide R6400v2, R6700v3,XR300:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399 Install guide R7800/XR500:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614 Forum Guide Lines (important read):https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324087
For the linksys EA6900 with Xvortex CFE, the MAC addresses are only properly initialized if you reset with WPS button (hold WPS button, unplug, wait 10 seconds, replug and wait approx. 25 seconds until linksys light flashes)
Resetting by GUI or erase nvram gets the same MAC addresses for both wireless. Maybe this can help you also
thank you. i tried your suggestion tree times without succes.
but really the Xvortex CFE causes this problem. i changed to koolshare CFE an now both radios have diffrenet MAC.
Router: Netgear WNDR3700v4
Firmware: DD-WRT v3.0-r30771 std
Kernel: 3.18.42
Reset: no
Errors: no
Note: Main AP
Router: Linksys E4200
Firmware: dd-wrt.v24-30771_NEWD-2_K3.x_mega-e4200.bin
Kernel: Forgot to look
Reset: yes/no
Errors: no
Note: Use as wireless bridge/repeater
Sorry for putting both in the same post, not sure if you wanted them separate but the issue is related to both.
I updated both to the latest build from 10/18/16 and both worked fine without error, except that my bridge WiFi speed was super slow (15mbps at best). I found Steve Jenkin's recommendation for the E4200 to not update to a K3.x version because of WiFi speed issues, so I rolled back to dd-wrt.v24-29739_NEWD-2_K2.6_mega-nv60k.bin and now my speeds are acceptable again. Before rolling back I did do a 30/30/30 and re-flash, as well as tweaking some settings but it was still slow.
Router: ASUS RT-N12 D1
Firmware: DD-WRT v3.0-r30771 mega (10/18/16)
Kernel: Linux 3.10.103 #14601 Tue Oct 18 12:31:14 CEST 2016 mips
Status: Working
Reset: no / Rebooting only
Errors: no
Note: use it as switch and AP.
No problems, but the GUI is a bit slower than the previous one.
