Your reports for Broadcom units are highly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:
This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 29621_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.
Router: Netgear R6300v1
Firmware: DD-WRT v3.0-r31690 giga (03/17/17)
Kernel: Linux R6300 3.10.105 #14122 Fri Mar 17 11:28:58 CET 2017 mips DD-WRT
Status: Good
Reset: No reset, upgraded through UI, came from dd-wrt.v24-31221_NEWD-2_K3.x_mega-R6300
Errors: None so far, minimal RX/TX errors, seems less than prior builds. Router came up flawlessly after rebooting after upgrade.
Config: Router is setup as main router/gateway as DMZ-host behind crappy router from ISP.
Update after 10 hours of use: r31690 still very stable. If this stays this way, I'm sticking with this one for a while. After scheduled daily reboot at midnight, router came back up fine, no issues whatsoever, lowest amount of TX/RX-errors I've seen for a long, long time. I like it
Last edited by MarCoMLXXV on Sat Mar 18, 2017 9:02; edited 1 time in total
Linksys E1200 v2
DD-WRT v3.0-r31690 mega (03/17/17)
Linux 3.10.105 #14138 Fri Mar 17 11:43:53 CET 2017 mips
conf as gateway w/guest on wl0.1
all good
66.22 Mbps best I got wired across WAN.
-------
erase nvram
erase linux
linksys FW mangament install dd-wrt.v24-31690_NEWD-2_K2.6_mini-e1200v2.bin
GUI install dd-wrt.v24-31690_NEWD-2_K2.6_mega-nv64k.bin
DD-WRT v3.0-r31690 mega (03/17/17)
Linux 2.6.24.111 #30997 Fri Mar 17 01:22:40 CET 2017 mips
conf as gateway
VAP on wl0.1 will not broadcast using WPA2 security
works ok using WEP
unbridge VAP in wireless settings ok
net isolation ok
NO buttons at all work on page 192.168.1.1/Networking.asp
Can conf DHCP in 'Additional DNSMasq Options' in Services page ... if you
do that you can have a good guest network using WEP security
...same ol mess k2.6 has been forever
88.56 Mbps best I got wired across WAN.
Posted: Sat Mar 18, 2017 15:09 Post subject: Asus RT-AC68 and Linksys E2000
Asus RT-AC68U
DD-WRT v3.0-r31690 std (03/17/17) (previous r31571)
Kernel: Linux 4.4.55-rc1 #1311 SMP Fri Mar 17 07:00:44 CET 2017 armv7l
2.4Ghz (NG-mixed) with 40Mhz channel width: Ok
5Ghz (Mixed) with 80Mhz channel width: Ok
SSH: Ok
Telnet: Disabled but tested to work
USB 2.0 storage ext3 mount to JFFS: Ok
USB 3.0 storage EXT3 mount to /mnt: Ok
Samba shared drive: Ok
Site Survey: Ok
Wi-viz Survey 2.4Ghz & 5Ghz: Ok
Reset: No
Status: Ok
Uptime: 39 minutes
CPU Temperature: CPU 75.8 °C / WL0 48.0 °C / WL1 47.6 °C
2 x E2000
DD-WRT v3.0-r31690 mega (03/17/17) (previous r31571)
Kernel:Linux 3.10.105 #14138 Fri Mar 17 11:43:53 CET 2017 mips
2.4Ghz (NG-mixed) with 40Mhz channel width: Ok
SSH: Ok
Telnet: Disabled but tested to work
Site Survey: Ok
Wi-viz Survey 2.4Ghz: Ok
Reset: No
Status: Ok
Uptime: 45 minutes
CPU Temperature: WL0 58.0 °C
All devices working as AP's each with individual 1Gb wired connections to main firewall
Router: Netgear R8500 MP1
Firmware: DD-WRT v3.0-r31690 std (03/17/17) (previously stock R8500-V1.0.2.86_1.0.75)
Kernel: Linux 4.4.55-rc1 #1316 SMP Fri Mar 17 07:33:17 CET 2017 armv7l
Status: Good
Reset: Yes
Errors: Internet LED not lit when uplinking through wl0 - client mode to hotspot.
Router: Linksys EA6500v2
Firmware: r31533 Kernel: Linux 4.4.55-rc1 #1311 SMP Fri Mar 17 07:00:44 CET 2017 armv7l
Previous: r31533 Status: 2.4GHz Broken. -80dBm@5ft; <1Mbps transfer rate. 5GHz works fine.
Reset: No. Disabled 2.4GHz, and re-enabled. Comes back good for 30 seconds then back to bad.
Errors: Two transmite errors on 2.4GHz; <5 on 5Ghz after few minutes.
Router: Netgear R8000
Firmware: DD-WRT v3.0-r31690 std (03/17/17)
Previous: Stock R8000-V1.0.3.36_1.1.25.chk
Kernel: Linux 4.4.55-rc1 #1316 SMP Fri Mar 17 07:33:17 CET 2017 armv7l
Status: Good
Reset: Yes
Errors: Internet LED not lit when uplinking through wl0 - client mode to hotspot.
Router: Netgear WNDR4300
Firmware: DD-WRT v3.0-r31571 std (03/04/17)
Kernel: Linux 3.18.48 #1736 Sat Mar 4 03:22:37 CET 2017 mips
Status: No 5G on Apple. No Internet Access: Revert to 31571
Reset: Tried to carry settings to fix apple issue
Errors: Couldn't get 5G to work to apple devices. After resetting defaults couldn't regain AP. Reset to 31571 to regain working AP.
Running stable five hours. No amazing load or wifi in use here, a few PCs with steady 60mpbs internet and an Android 'N' phone or three.
Your reports for Broadcom units are highly appreciated !
Router: WNDR4000v1
Firmware: DD-WRT v3.0-r31690 (03/17/17), up from dd-wrt.v24-27506_NEWD-2_K3.x_mega-nv64k
Kernel: Linux 3.10.105 #14138 Fri Mar 17 11:43:53 CET 2017 mips
Status: Without Issue
Reset: 30-30-30, then GUI Factory'd without reset per the necessity for this model, then GUI flashed, GUI Factory'd and configured.
Errors: None. Have not tried 5G, previously it would tank the unit and was said to be unusable, doubtful it is better.
