Router Model: Linksys EA6400
Firmware Version: DD-WRT v3.0-r33006 std (08/03/17)
Kernel Version: Linux 4.4.79 #1798 SMP Wed Aug 2 10:41:19 CEST 2017 armv7l
CPU Model: Broadcom BCM4708
CPU Clock: 1200 MHz
CPU Temperature: CPU 69.1 °C / WL0 46.5 °C / WL1 55.9 °C
Current Time: ???
Uptime: 2 days, 8:25
Mode/Status: WL1: Repeater Bridge(AC Only), WL0: AP (NG-Mixed)
USB/NAS: Enabeld
Reset: No
Upgraded with WebGUI (Finally works)
Issues/Errors: Current Time doesn't work.
Router/Version: Linksys EA6900
Firmware: v3.0-r33006 std (08/03/17)
Kernel: Linux 4.4.79 #1798 SMP Wed Aug 2 10:41:19 CEST 2017 armv7l
Previous: stock
Mode/Status: working
Reset: none
Issues/Errors: none after disabling usb support
reset randomly when leaving the usb support enabled.
I switched over to K2.4 and almost everything works, except it still doesn't save some settings, and when I reboot the device, I need to disable the security and re-enable it. If I don't, it works like when I had the K2.6 version installed and no secured APs are visible.
Also, it seems to randomly enable security on the open virtual SSIDs I've setup. When that happens, just like the normal SSIDs, I have to disable security before it will show itself after a reboot. The problem with it not enabling one or more SSIDs because of encryption is mostly limited to the 2.4GHz band, but I just restarted it before this post and it happened on my 5GHz virtual SSID.[/url]
Router/Version: D-Link 868L Rev. A
Firmware: v3.0-r33006 std (08/03/17)
Kernel: Linux 4.4.79 #1798 SMP Wed Aug 2 10:41:19 CEST 2017 armv7l
Previous: r28647
Mode/Status: bricked
Reset: yes
Issues/Errors: This model and the D-Link 880 continues to brick. Can any of the devs please test/fix these models? This has been going on for a long time now.
Router/Version: Asus RT-N16 Firmware: dd-wrt.v24-33006_NEWD-2_K3.x_big.bin Kernel:3.10.107 Previous: Unknown Mode/Status: AP Reset: From GUI and erase nvram Issues/Errors: Working good in the beginning, but now I can't get any IP address from the DHCP when connecting with wifi
Update, the wifi started to work again after GUI reset, dhcp works again
Router/Version: D-Link 868L Rev. A
Firmware: v3.0-r33006 std (08/03/17)
Kernel: Linux 4.4.79 #1798 SMP Wed Aug 2 10:41:19 CEST 2017 armv7l
Previous: r28647
Mode/Status: bricked
Reset: yes
Issues/Errors: This model and the D-Link 880 continues to brick. Can any of the devs please test/fix these models? This has been going on for a long time now.
Uhgg...Welp, thx for testing. So much for my attempt at that one after reading what you said lol. Was looking through all of this hoping one of them would show up with good results. All three (890/880/868)seem to have issues, but like you pointed out, it's been an ongoing problem for quite some time. r30432 works superbly on my 880 but it's a year old now. No idea what could have caused so many issues for so long. Was hoping to get a look at this new toys they added.
Router/Version: D-Link 868L Rev. A
Firmware: v3.0-r33006 std (08/03/17)
Kernel: Linux 4.4.79 #1798 SMP Wed Aug 2 10:41:19 CEST 2017 armv7l
Previous: r28647
Mode/Status: bricked
Reset: yes
Issues/Errors: This model and the D-Link 880 continues to brick. Can any of the devs please test/fix these models? This has been going on for a long time now.
Uhgg...Welp, thx for testing. So much for my attempt at that one after reading what you said lol. Was looking through all of this hoping one of them would show up with good results. All three (890/880/868)seem to have issues, but like you pointed out, it's been an ongoing problem for quite some time. r30432 works superbly on my 880 but it's a year old now. No idea what could have caused so many issues for so long. Was hoping to get a look at this new toys they added.
Well I'm guessing that the Netgear models having the same problem since 30432 will brick too, I was hoping that with this size shrunk build would be solved. Try Kong, it should work. _________________ R6400v2 (boardID:30) - Kong 36480 running since 03/09/18 - (AP - DNSMasq - AdBlocking - QoS) R7800 - BS 31924 running since 05/26/17 - (AP - OpenVPN Client - DNSMasq - AdBlocking - QoS) R7000 - BS 30771 running since 12/16/16 - (AP - NAS - FTP - SMB - OpenVPN Server - Transmission - DDNS - DNSMasq - AdBlocking - QoS) R6250 - BS 29193 running since 03/20/16 - (AP - NAS - FTP - SMB - DNSMasq - AdBlocking)
On my rt-ac3100, I can't connect to the 2.4ghz regardless of the mode setting when I select channel 6 which is the best in my area.
It keeps saying incorrect password, cannot connect.
If I change to channel 11, not optimal, I can connect.
I also had to downgrade using the recovery option. Kept rebooting into 33006 if I tried o downgrade to a previously working build. _________________ I am far from a guru, I'm barely a novice.
Router Model: Linksys EA6400
Firmware Version: DD-WRT v3.0-r33010M kongac (08/09/17)
Kernel Version: Linux 4.4.80 #422 SMP Wed Aug 9 20:13:10 CEST 2017 armv7l
Current Time: Mon, 21 Aug 2017 20:41:41
Uptime: 11 days, 23:21
at startup, i get this in dmesg:
br0: port 4(eth2) entered forwarding state
br0: port 3(eth1) entered forwarding state
br0: port 2(vlan2) entered forwarding state
br0: port 1(vlan1) entered forwarding state
random: nonblocking pool is initialized
after some indeterminate period of time, the router slows down signficatnly and i get this addtional message:
nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
It was asked here once, no reply. I thought Kong did reply about it once, but couldn't find anything. _________________ #NAT/SFE/CTF: limited speed w/ DD#Repeater issues#DD-WRT info: FAQ, Builds, Types, Modes, Changes, Demo#
OPNsense x64 5050e ITX|DD: DIR-810L, 2*EA6900@1GHz, R6300v1, RT-N66U@663, WNDR4000@533, E1500@353,
WRT54G{Lv1.1,Sv6}@250|FreshTomato: F7D8302@532|OpenWRT: F9K1119v1, RT-ACRH13, R6220, WNDR3700v4
Router/Version: Trendnet TEW811DRU
Firmware: DD-WRT v3.0-r33006 mini (08/03/17)
Kernel: Linux 4.4.79 #1801 Thu Aug 3 07:41:58 CEST 2017 armv7l
Previous: DD-WRT v3.0-r30805 mini (10/27/16)
Mode/Status: AC-only client bridge
Reset: No
Issues/Errors: None so far
Firmware: DD-WRT v3.0-r33006 mega (08/03/17)
Kernel: Linux 3.10.107 #15472 Thu Aug 3 12:11:03 CEST 2017 mips
Status: Working over 1 day uptime
Reset: YES, (upgraded from aging Tomato Build)
Errors: None.
From Default Enabled Features...
- Disabled SFE
- IPv4 + HE IPv6 via 6in4 Static Tunnel
- GUI Firewall & Startup Scripts
- 2.4Ghz Radio with 2 SSIDs (BW 20Mhz)
- 5Ghz Radio (BW 40Mhz)
- WAN port -> DSL Modem
- DNSCrpyt v1.9.5 via entware-ng for IPv4 & IPv6 (Thanks to James2K)
- NTP with Blank IP
- Cron Job - Monitor WAN, IPv6 & DNS Connections
- DDNS Custom with DNSoMatic
- 3 BRs, 3 VLANS & 4 Assignments
- SSH (WAN Access), Telnet & Syslog
- WAN Traffic Disabled
- USB Storage (NTFS) with Auto Mount
- entware-ng installed
- YAMon 3.3.2 installed
UPDATE...
I had daily Router reboot issues during the heaviest usage. Removing the overclock of 533Mhz to 480Mhz fixed the problem. _________________ Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9
Off Site 1
R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4
Off Site 2
R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531
Was hoping to get a look at this new toys they added.