New BS build available : DD-WRT v3.0-r33555 std (10/20/17)

Post new topic   Reply to topic    DD-WRT Forum Index -> Atheros WiSOC based Hardware
Goto page Previous  1, 2, 3, 4, 5, 6  Next
Author Message
tatsuya46
DD-WRT Guru


Joined: 03 Jan 2010
Posts: 7568
Location: YWG, Canada

PostPosted: Tue Oct 24, 2017 21:35    Post subject: Reply with quote
labo wrote:
Router: R9000
Firmware: DD-WRT v3.0-r33555 std (10/20/17)
Kernel: Linux 4.9.57 #82 SMP PREEMPT Thu Oct 19 01:15:09 CEST 2017 armv7l
Status: Working well
Reset: No
Errors: None so far.

4+days on R9000. SFE enabled, QOS enabled, no reboot issues.
AD chip MAC address reports correctly again now, instead all zeros in the last few builds.
Sold build. Thanks! BS.


so sfe is off, cause qos is on. unless u manually entered the command to force sfe on with qos (pointless, no downlink control but its doable). im assuming u didnt do that or it probably would of been mentioned

_________________
LATEST FIRMWARE(S)

BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers

[x86_64] Haswell i3-4150/QCA9984/QCA9882 ------> r55488 std
[QUALCOMM] DIR-862L --------------------------------> r55460 std
▲ ACTIVE / INACTIVE ▼
[QUALCOMM] WNDR4300 v1 --------------------------> r50485 std
[BROADCOM] DIR-860L A1 ----------------------------> r50485 std


Sigh.. why do i exist anyway.. | I love you Anthony.. never forget that.. my other 99% that ill never see again..

Sponsor
inodoro
DD-WRT Novice


Joined: 19 Oct 2017
Posts: 2

PostPosted: Tue Oct 24, 2017 22:01    Post subject: Reply with quote
Router: TP-Link TL-WR941ND v3.6
Firmware: DD-WRT v3.0-r33555 std (10/20/17)
Kernel: Linux 3.10.107 #41928 Fri Oct 20 03:11:43 CEST 2017 mips
Status: Good
Reset: Yes
Errors: No

Updated 2 hours ago using the web GUI from build 29519. So far so good.

Thanks!
labo
DD-WRT Guru


Joined: 30 Jan 2015
Posts: 676
Location: Texas, USA

PostPosted: Wed Oct 25, 2017 0:03    Post subject: Reply with quote
tatsuya46 wrote:
labo wrote:
Router: R9000
Firmware: DD-WRT v3.0-r33555 std (10/20/17)
Kernel: Linux 4.9.57 #82 SMP PREEMPT Thu Oct 19 01:15:09 CEST 2017 armv7l
Status: Working well
Reset: No
Errors: None so far.

4+days on R9000. SFE enabled, QOS enabled, no reboot issues.
AD chip MAC address reports correctly again now, instead all zeros in the last few builds.
Sold build. Thanks! BS.


so sfe is off, cause qos is on. unless u manually entered the command to force sfe on with qos (pointless, no downlink control but its doable). im assuming u didnt do that or it probably would of been mentioned


Nope, in this build I'm able to turn on both SFE and QOS, no issues.

_________________
ASUS GT-BE98 PRO Main: Fiber 5gbps up/down
ASUS AXE16000: AI Mesh node
2 X ASUS RT-AX89X: AI Mesh nodes
QNAP QSW-1208-8C 12-Port 10GbE Switch
XS712T ProSafe 12-Port 10GbE Switch
3 X R9000 DD-WRT Mesh
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 6268
Location: Texas

PostPosted: Wed Oct 25, 2017 0:32    Post subject: Reply with quote
labo wrote:
Nope, in this build I'm able to turn on both SFE and QOS, no issues.

She don't do that with r33555 on the EA8500.
QOS on = SFE off
It will still show enabled in the webif but she is lyin'
::::: then on the other other side :::::
Kong r33545M
SFE will stay running if QOS is turned on.

Been this way for while now Cool
labo
DD-WRT Guru


Joined: 30 Jan 2015
Posts: 676
Location: Texas, USA

PostPosted: Wed Oct 25, 2017 0:55    Post subject: Reply with quote
How do I check from command line if SFE and QOS are on or off?
_________________
ASUS GT-BE98 PRO Main: Fiber 5gbps up/down
ASUS AXE16000: AI Mesh node
2 X ASUS RT-AX89X: AI Mesh nodes
QNAP QSW-1208-8C 12-Port 10GbE Switch
XS712T ProSafe 12-Port 10GbE Switch
3 X R9000 DD-WRT Mesh
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 6268
Location: Texas

PostPosted: Wed Oct 25, 2017 1:03    Post subject: Reply with quote
labo wrote:
How do I check from command line if SFE and QOS are on or off?
run
Code:
lsmod

if shortcut_fe not in da list then she aint active
labo
DD-WRT Guru


Joined: 30 Jan 2015
Posts: 676
Location: Texas, USA

PostPosted: Wed Oct 25, 2017 1:20    Post subject: Reply with quote
Yes, Thanks. Enabling QOS disables SFE, though in the GUI it is still sows as enabled.
When I disable QOS, I can see two modules with shortcut_fe shows up with lsmod command.

_________________
ASUS GT-BE98 PRO Main: Fiber 5gbps up/down
ASUS AXE16000: AI Mesh node
2 X ASUS RT-AX89X: AI Mesh nodes
QNAP QSW-1208-8C 12-Port 10GbE Switch
XS712T ProSafe 12-Port 10GbE Switch
3 X R9000 DD-WRT Mesh
tatsuya46
DD-WRT Guru


Joined: 03 Jan 2010
Posts: 7568
Location: YWG, Canada

PostPosted: Wed Oct 25, 2017 1:40    Post subject: Reply with quote
labo wrote:
Yes, Thanks. Enabling QOS disables SFE, though in the GUI it is still sows as enabled.
When I disable QOS, I can see two modules with shortcut_fe shows up with lsmod command.


only in kong build sfe can be enabled with qos (no downlink support though), in bs builds gui still shows enabled, when its not

unless u give the router a command to manually enable sfe

_________________
LATEST FIRMWARE(S)

BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers

[x86_64] Haswell i3-4150/QCA9984/QCA9882 ------> r55488 std
[QUALCOMM] DIR-862L --------------------------------> r55460 std
▲ ACTIVE / INACTIVE ▼
[QUALCOMM] WNDR4300 v1 --------------------------> r50485 std
[BROADCOM] DIR-860L A1 ----------------------------> r50485 std


Sigh.. why do i exist anyway.. | I love you Anthony.. never forget that.. my other 99% that ill never see again..

labo
DD-WRT Guru


Joined: 30 Jan 2015
Posts: 676
Location: Texas, USA

PostPosted: Wed Oct 25, 2017 1:49    Post subject: Reply with quote
OK, I enabled SFE from command line
Code:

insmod shortcut-fe

with QOS enabled and was able see the two modules loaded.
Hope it is now enabled. Let's see if reboots as it used to do previously...

_________________
ASUS GT-BE98 PRO Main: Fiber 5gbps up/down
ASUS AXE16000: AI Mesh node
2 X ASUS RT-AX89X: AI Mesh nodes
QNAP QSW-1208-8C 12-Port 10GbE Switch
XS712T ProSafe 12-Port 10GbE Switch
3 X R9000 DD-WRT Mesh
labo
DD-WRT Guru


Joined: 30 Jan 2015
Posts: 676
Location: Texas, USA

PostPosted: Wed Oct 25, 2017 1:57    Post subject: Reply with quote
So the downside of enabling SFE with QOS is no downlink control. But uplink QOS will work?
I only need the uplink control for my VOIP phone to work well.

_________________
ASUS GT-BE98 PRO Main: Fiber 5gbps up/down
ASUS AXE16000: AI Mesh node
2 X ASUS RT-AX89X: AI Mesh nodes
QNAP QSW-1208-8C 12-Port 10GbE Switch
XS712T ProSafe 12-Port 10GbE Switch
3 X R9000 DD-WRT Mesh
tatsuya46
DD-WRT Guru


Joined: 03 Jan 2010
Posts: 7568
Location: YWG, Canada

PostPosted: Wed Oct 25, 2017 4:06    Post subject: Reply with quote
labo wrote:
So the downside of enabling SFE with QOS is no downlink control. But uplink QOS will work?
I only need the uplink control for my VOIP phone to work well.


only uplink will work with sfe on with qos..

have someone download when ur using voip, ull probably sing a different tune..

_________________
LATEST FIRMWARE(S)

BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers

[x86_64] Haswell i3-4150/QCA9984/QCA9882 ------> r55488 std
[QUALCOMM] DIR-862L --------------------------------> r55460 std
▲ ACTIVE / INACTIVE ▼
[QUALCOMM] WNDR4300 v1 --------------------------> r50485 std
[BROADCOM] DIR-860L A1 ----------------------------> r50485 std


Sigh.. why do i exist anyway.. | I love you Anthony.. never forget that.. my other 99% that ill never see again..

mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 6268
Location: Texas

PostPosted: Fri Oct 27, 2017 6:04    Post subject: Reply with quote
mrjcd wrote:
WNDR3700 V4
DD-WRT v3.0-r33555 std (10/20/17)
Linux 3.18.76 #983 Fri Oct 20 04:14:41 CEST 2017 mips
No Reset
He's working ok.

runnin as a WAP -- all ok
~# uptime
00:45:57 up 5 days, 22:40

mrjcd wrote:
EA8500
DD-WRT v3.0-r33555 std (10/20/17)
Linux 3.18.76 #186 SMP PREEMPT Thu Oct 19 01:36:58 CEST 2017 armv7l
No Reset
He's working ok.

primary router -- no grief here Cool
~# uptime
00:39:01 up 5 days, 22:36
~# date
Fri Oct 27 00:39:06 CDT 2017
dan_danananda
DD-WRT Novice


Joined: 09 Nov 2013
Posts: 35

PostPosted: Sun Oct 29, 2017 14:31    Post subject: Reply with quote
numerci wrote:
33555 works better than the 33006 on Archer C7 V2. Faster boot time, faster speeds on Wi-Fi.


When did the improvements come? just on this build?
numerci
DD-WRT User


Joined: 02 May 2012
Posts: 134

PostPosted: Sun Oct 29, 2017 15:02    Post subject: Reply with quote
Faster boot time since 33525. Faster WiFi I have noted only on this one.
Wildlion
DD-WRT Guru


Joined: 24 May 2016
Posts: 1407

PostPosted: Sun Oct 29, 2017 21:41    Post subject: Reply with quote
Router: DIR-615e3
Firmware: dir615e3-firmware.bin (v3.0-r33555 std)
Kernel: Linux 3.10.107 #41914 Fri Oct 20 03:00:58 CEST 2017 mips
Status: Working
Reset: No
Notes on configuration:

    DNSMasq
    Virtual wireless with bridging x2
    multiple DHCP server
    QOS

Errors:

    None





Router: DIR-825 rev B1
Firmware: dir825-firmware.bin (v3.0-r33555 std)
Kernel: Linux 3.10.107 #41896 Fri Oct 20 02:30:07 CEST 2017 mips
Status: Working
Reset: No
Notes on configuration:

    Media Network
    DNSMasq
    Port Forwarding

Errors:


    None
Goto page Previous  1, 2, 3, 4, 5, 6  Next Display posts from previous:    Page 5 of 6
Post new topic   Reply to topic    DD-WRT Forum Index -> Atheros WiSOC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum