[SOLVED] linksys e2000 with sfe maxed out at ~100mbps?

Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware
View previous topic :: View next topic  
Author Message
maurer
DD-WRT User


Joined: 22 Jun 2009
Posts: 104
PostPosted: Tue Apr 10, 2018 11:58    Post subject: [SOLVED] linksys e2000 with sfe maxed out at ~100mbps? Reply with quote
I've upgraded my linksys e2000 to latest dd-wrt k3.0 with SFE enabled in wan settings (default dhcp) but i cannot seem to get more than 100mbps in speedtests.
I was hoping to get as near as possible to my contract's 300/150.
upstream modem shows 1G link
I've also tested latest tomato shibby and with bcm_nat loaded i can get ~130mbps.
is someone getting more out of this old linksys ?

thanks

Last edited by maurer on Wed Apr 11, 2018 7:46; edited 1 time in total
Back to top View user's profile Send private message
Sponsor
myersw
DD-WRT Guru


Joined: 13 Jun 2006
Posts: 1608
Location: SE Michigan USA
PostPosted: Tue Apr 10, 2018 16:29    Post subject: Reply with quote
According to this post it may be new router time. Sounds like the e2000 cannot go faster.

http://community.linksys.com/t5/Wireless-Routers/E2000-wired-download-speed-issue/td-p/1027124

Read through it and you will find where 95 seems about it for this router.
_________________
Unifi Security Gateway: Unifi Firmware
Netgear r7800: Voxel Firmware
Modem:Netgear CM500V voice and Data.
ISP:Comcast
tutorial for flashing "WRT" series:
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=287813
DD-WRT Installation, Upgrade & Basic Setup–Cliff Notes:
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=311117
Kong DD-WRT Config Tutorial:
http://www.instructables.com/id/Install-and-Configure-a-DD-WRT-Kong-Router/
I tried to be normal once. Worst 2 minutes ever.
Back to top View user's profile Send private message
maurer
DD-WRT User


Joined: 22 Jun 2009
Posts: 104
PostPosted: Tue Apr 10, 2018 16:43    Post subject: Reply with quote
i was too fast to judge Smile just needed more testing
directly plugged as pppoe client:

Back to top View user's profile Send private message
jwh7
DD-WRT Guru


Joined: 25 Oct 2013
Posts: 2670
Location: Indy
PostPosted: Tue Apr 10, 2018 18:39    Post subject: Re: linksys e2000 with sfe maxed out at ~100mbps? Reply with quote
maurer wrote:
I've upgraded my linksys e2000 to latest dd-wrt k3.0 with SFE enabled in wan settings (default dhcp) but i cannot seem to get more than 100mbps in speedtests.
I was hoping to get as near as possible to my contract's 300/150.
It should be getting over 100 Mb/s w/ SFE. You're testing wired I presume. What other settings have you changed from a reset (and manual set up)? And what build?

Edit: oh, your speedtest pic wasn't showing for me before. So it's working now? What did you change/do?
_________________
# NAT/SFE/CTF: limited speed w/ DD # Repeater issues # DD-WRT info: FAQ, Builds, Types, Modes, Changes, Demo #
OPNsense x64 5050e ITX|DD: DIR-810L, 2*EA6900@1GHz, R6300v1, RT-N66U@663, WNDR4000@533, E1500@353,
WRT54G{Lv1.1,Sv6}@250|FreshTomato: F7D8302@532|OpenWRT: F9K1119v1, RT-ACRH13, R6220, WNDR3700v4
Back to top View user's profile Send private message
maurer
DD-WRT User


Joined: 22 Jun 2009
Posts: 104
PostPosted: Wed Apr 11, 2018 7:46    Post subject: Reply with quote
just plugged/configured it instead of main gateway as pppoe client - initially i was using it with dhcp wan (defaults) as a double nat device for speedtests
except this everything is factory default
Back to top View user's profile Send private message
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum