New Build 40443: BS 07-27-2019-r40443

Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware
Author Message
kernel-panic69
DD-WRT Guru


Joined: 08 May 2018
Posts: 14221
Location: Texas, USA

PostPosted: Sat Jul 27, 2019 21:09    Post subject: New Build 40443: BS 07-27-2019-r40443 Reply with quote
Downloads: (if a link doesn't work, try another)
https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2019/07-27-2019-r40443/
ftp://ftp.dd-wrt.com/betas/2019/07-27-2019-r40443/
Alternate link: DD-WRT website
Note: to use wget (or curl) for CLI flash (`write {f/w} linux`), change the https to http (or use ftp instead)

Changelogs:
SVN* changelog since last build: 40439
Summary: (deprecated after 29739)
*Github mirror: https://github.com/mirror/dd-wrt/

Notes:
1. SFE accelerated NAT is in 33006+ builds but only in kernel 3.2 and newer
2. 'KRACK' vulnerability fixes were completed in r33678 for Broadcom, including k26 (33655) & k24 (33656); use build 33772 or later.
3. Bridge modes on k4.4 devices may sometimes work in some configurations in certain builds but are not supported by the bcmdhd driver. Use client or repeater instead as WDS doesn't work with Broadcom ARM either (see Issues below).
4. Since 39469, udhcpd was removed and replaced with the already present dnsmasq, and PIE qdisc was added for some builds.
5. Policy-Based Routing with SFE enabled was fixed in r39556: 5986 and 5900
6. k2.4 (broadcom/) builds were fixed in 39715 (broken in 39144 through 39654)
7. SFE update (k3.10+ for BCM) was in the 39927 build.


Issues, observations, and/or workarounds reported:
1. Trendnet 81*DRU models are missing factory-to-flash
2. DNScrypt is mostly only using v2 protocols now, but requires Golang that DD can't use: 6246
3. WDS does not work on Broadcom ARM devices (only MIPS<->MIPS)
4. K2.6 builds are broken since 38253(?) (GUI issues): 6538
5. VAPs not working at boot; workaround startup command:
sleep 10;stopservice nas;stopservice wlconf;startservice wlconf;startservice nas
This appears to be fixed for some routers (different kernels, modes, and radios) since build 39508.
6. UDP forwarding might not work with SFE Enabled: 6668


Important: if any issues are found, please provide log info (GUI syslog, `dmesg`, `cat /var/log/messages`).
Or put into SVN ticket. For firewall issues, also provide "iptables" info (`iptables -L`, `iptables -t nat -L`, & the /tmp/.ipt file).

Template to copy (after "Code:") for posting issues, be sure to include the mode in use (gateway, AP, CB, etc.):
Code:
[b]Router/Version: [/b]
[b]File: [/b]
[b]Kernel: [/b]
[b]Mode: [/b]
[b]Status: [/b]

WARNING: This thread is to report on flashing this experimental test build, providing important info for both developers and users. Always state your hardware model, version, mode (e.g. Repeater) and SPECIFIC build (e.g. 33555_NEWD-2_K3.x_mega-nv64k.bin). Please avoid discussions and create a new thread to discuss specific problems or questions, as this thread is for reporting, not support. Posts may be deleted or moved to keep this thread manageable and useful. If you don't understand the risks or what to flash and how, with a means of recovery if it bricks, do NOT flash this experimental test build.
Sponsor
mrjcd
DD-WRT Guru


Joined: 31 Jan 2015
Posts: 6290
Location: Texas

PostPosted: Sat Jul 27, 2019 21:35    Post subject: Reply with quote
Asus RT-N12B ....NOTE: this is actually the Asus RT-N12D1
DD-WRT v3.0-r40443 mega (07/27/19)
Linux 3.10.108-d8 #25563 Sat Jul 27 15:36:47 +04 2019 mips
dd-wrt.v24-40443_NEWD-2_K3.x_mega.bin
just used as a WAP
all good so far -- see its 'dmesg'
GUI install over r40274 _ NO Reset

2nd. RT-N12D1 used for testing
reset to DD-WRT defaults and create a VAP

#

E2500
DD-WRT v3.0-r40443 mega (07/27/19)
Linux 3.10.108-d8 #25563 Sat Jul 27 15:36:47 +04 2019 mips
dd-wrt.v24-40443_NEWD-2_K3.x_mega.bin
ok

#

E1200v2
Firmware Version DD-WRT v3.0-r40443 mega (07/27/19)
Kernel VersionLinux 3.10.108-d8 #25563 Sat Jul 27 15:36:47 +04 2019 mips
dd-wrt.v24-40443_NEWD-2_K3.x_mega-nv64k.bin
ok

#
same ol broadcom VAP crap on all 3 these units
You have to 'Apply Settings' in ../Wireless_Basic.asp OR ../WL_WPATable.asp
OR
use a startup workaround script
wuruxu
DD-WRT Novice


Joined: 17 Jun 2019
Posts: 15

PostPosted: Sat Jul 27, 2019 23:58    Post subject: Reply with quote
EA6300
Firmware: DD-WRT v3.0-r40443 std (07/27/19)
Kernel Linux 4.4.186 #546 SMP PREEMPT Sat Jul 27 12:36:57 +04 2019 armv7l

OK, but VAP cann't work correct

#
You have to 'Apply Settings' in ../Wireless_Basic.asp OR ../WL_WPATable.asp
OR
use a startup workaround script
flyzipper
DD-WRT Guru


Joined: 21 Feb 2016
Posts: 504

PostPosted: Sun Jul 28, 2019 0:19    Post subject: Reply with quote
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r40443 std (07/27/19)
Kernel: Linux 4.4.186 #546 SMP PREEMPT Sat Jul 27 12:36:57 +04 2019 armv7l
Previous: r40400 (recovered to after failed r40439)
Mode/Status: Gateway / working
Reset: no
Issues/Errors: Working so far, but will test Xbox Live party chat with SFE enabled... later (suspect problems are related to UDP forwarding not fully working with SFE Enabled: 6668).

Edit1... yep, Xbox Live party chat still has problems when SFE enabled.

Edit2... have been having network drops, before blaming this build, will reset and manually configure to see if they're due to the failed 40439 and associated recovery calisthenics.

Edit3... reset and manually configured, will watch for 24hrs to see if it's now stable.

Uptime: 20min
Temperatures: CPU 54.7 °C / WL0 38.6 °C / WL1 44.9 °C


Last edited by flyzipper on Sun Jul 28, 2019 21:30; edited 3 times in total
Gradius
DD-WRT Novice


Joined: 11 May 2013
Posts: 45
Location: Chile

PostPosted: Sun Jul 28, 2019 5:03    Post subject: Reply with quote
Router/Version: TP-Link C9 v1
Build: DD-WRT v3.0-r40443 std (07/27/19)
Status: Working

Been up 10min, no problem so far.

Temps a bit high (been UP over 24h since last flash):
CPU 64.7 °C / WL0 46.5 °C / WL1 48.6 °C
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum