Joined: 16 Nov 2015 Posts: 6407 Location: UK, London, just across the river..
Posted: Fri Feb 02, 2018 9:50 Post subject:
Router Model TPLINK WR1043ND V2
Firmware Version DD-WRT v3.0-r34777 std (01/31/1
Kernel Version Linux 3.18.93-rc1 #6973 Wed Jan 31 05:38:51 CET 2018 mips
update: via GUI
status: operational
reset: No
errors: none for my set up so far so good 3h up and running... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55179 WAP
TP-Link WR1043NDv2 -DD-WRT 55303 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55460 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55460 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55363 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Gosh...next time is going to be a hashtag on twitter announcing a new build. _________________ R6400v2 (boardID:30) - Kong 36480 running since 03/09/18 - (AP - DNSMasq - AdBlocking - QoS) R7800 - BS 31924 running since 05/26/17 - (AP - OpenVPN Client - DNSMasq - AdBlocking - QoS) R7000 - BS 30771 running since 12/16/16 - (AP - NAS - FTP - SMB - OpenVPN Server - Transmission - DDNS - DNSMasq - AdBlocking - QoS) R6250 - BS 29193 running since 03/20/16 - (AP - NAS - FTP - SMB - DNSMasq - AdBlocking)
Posted: Fri Feb 02, 2018 14:31 Post subject: Netgear 7500v2 - no WIFI
Router Model Netgear 7500v2
Firmware Version DD-WRT v3.0-r34777 std
update: via GUI
status: partially operational
reset: No
errors: No wifi (unhappy elves), no voltage control, thermal sensors no work,
time stamps incorrect in logs
--errors--
msm_bus_fabric_init_driver
Calibration not found.
qcom-tsens 900000.thermal-sensor: tsens calibration failed
CPUidle arm: CPU 0 failed to init idle CPU ops
of: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:0, -19
of: dev_pm_opp_of_cpumask_add_table: couldn't find opp table for cpu:1, -19
ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin
ath10k_pci 0000:01:00.0: refusing to parse invalid tlv length 0
ath10k_pci 0000:01:00.0: failed to initialize code swap segment: -22
ath10k_pci 0000:01:00.0: could not probe fw (-22)
ath10k_pci 0001:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0040,subsystem-vendor=168c,subsystem-device=0002 from ath10k/QCA99X0/hw2.0/board-2.bin
ath10k_pci 0001:01:00.0: refusing to parse invalid tlv length 0
ath10k_pci 0001:01:00.0: failed to initialize code swap segment: -22
ath10k_pci 0001:01:00.0: could not probe fw (-22)
qcom-dwc3-usb-phy 100f8830.phy: cannot get HSIO settings from device node, using default values
qcom-dwc3-usb-phy 110f8830.phy: cannot get HSIO settings from device node, using default values
--warnings--
1b500000.pci supply vdda not found, using dummy regulator
1b500000.pci supply vdda_phy not found, using dummy regulator
1b500000.pci supply vdda_refclk not found, using dummy regulator
1b700000.pci supply vdda not found, using dummy regulator
1b700000.pci supply vdda_phy not found, using dummy regulator
1b700000.pci supply vdda_refclk not found, using dummy regulator
/cpus/cpu@0: unsupported enable-method property: qcom,kpss-acc-v1
nf_conntrack_rtsp v0.7 loading
nf_nat_rtsp v0.7 loading
ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2
ath10k_pci 0000:01:00.0: Falling back to user helper
ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2
ath10k_pci 0000:01:00.0: Falling back to user helper
ath10k_pci 0000:01:00.0: failed to initialize fw code swap segment: -22
ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0001:01:00.0.bin failed with error -2
ath10k_pci 0001:01:00.0: Falling back to user helper
ath10k_pci 0001:01:00.0: Direct firmware load for ath10k/QCA99X0/hw2.0/firmware-6.bin failed with error -2
ath10k_pci 0001:01:00.0: Falling back to user helper
ath10k_pci 0001:01:00.0: failed to initialize fw code swap segment: -2
Joined: 13 Aug 2013 Posts: 6856 Location: Romerike, Norway
Posted: Sat Feb 03, 2018 16:27 Post subject:
Router: Netgear R7800
Kernel: Linux 4.9.79-rc1 #43 SMP PREEMPT Tue Jan 30 01:57:29 CET 2018
Status: Issues
Reset: no
Errors: 5 Ghz set to VHT80, but clients connect as VHT20 or VHT40
Router Model: TP-Link TL-WR1043ND V1
Firmware Version: DD-WRT v3.0-r34777 std (01/31/18)
Reset: Yes.
Errors: Web upgrade fails. Must be updated manually/via serial. AR7100 flash code (ar7100_flash.c) needs the same changes that AR7240 flash code (ar7240_flash.c) got in change 33405: http://svn.dd-wrt.com/changeset/33405
Firmware can be updated manually via serial and still functions, just cannot flash in web UI. This is ridiculous, I've already spelled out how to fix it, it would take 2 seconds of time. You can't get a better bug report than that.
Posted: Sat Feb 03, 2018 18:12 Post subject: Upgrade
Router/Version: TP-Link Archer C7 v2
Firmware: 34777
Previous: 34578
Mode/Status: WDS AP, WDS Station
Reset: No
Issues/Errors: None, so far.
Router/Version: TP-Link WDR3600 v1
Firmware: 34777
Previous: 34578
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far.
Router/Version: TP-Link TL-WR841ND v8
Firmware: 34777
Previous: 34578
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far.
Router/Version: D-Link DIR-825 B1
Firmware: 34777
Previous: 34578
Mode/Status: WDS Station
Reset: No
Issues/Errors: None, so far.
Router/Version: D-Link DIR-862L A1
Firmware: 34777
Previous: 34578
Mode/Status: WDS Station
Reset: Yes.
Issues/Errors: None, so far. _________________ Before asking a question on the forums, update dd-wrt: Where do I download firmware? I suggest reading it all.
QCA Best WiFi Settings
Some dd-wrt wiki pages are up to date, others are not. PM me if you find an old one.
Atheros:
Netgear R7800 x3 - WDS AP / station, gateway, QoS
TP-Link Archer C7 v2 x2 - WDS Station
TP-Link TL-WDR3600 v1 - WDS Station
TP-Link 841nd v8 - NU
D-Link 615 C1/E3/I1 x 7 - 1 WDS station
D-Link 825 B1 - NU
D-Link 862L A1 x2 - WDS Station
Netgear WNDR3700v2 - NU
UBNT loco M2 x2 - airOS
Broadcom
Linksys EA6400 - Gateway, QoS
Asus N66U - AP
Netgear WNDR3700v3 - not used
MediaTek
UBNT EdgeRouter X - switch
Posted: Sat Feb 03, 2018 20:24 Post subject: Maybe weird DNS issues
Router/Version: TP-Link WDR4300
Firmware: 34777
Previous: 34311
Mode/Status: AP
Reset: No
Issues/Errors: I'm guessing some kind of dns problem. Because only a few sites are accessible (eg. Google, Facebook etc.). Yahoo, dd-wrt.com and the vast majority of the internet is not accessible by any wired or wireless client. The connection type is PPPOE and as soon as i remove the router from the equation (i connect the fiber modem to the pc) it works fine, so it is definitely not an isp issue. Reverted to 34311 and it appears to be working fine. There may be some setting that has been modified or needs enabling in the new builds, because i have been bit by something similar a few years back while setting an old router as a repeater bridge (i think).
I also have 34777 installed on a tp link wr841nd v11 and a couple of dlink dir615 (rev d and h), but they are secondary routers and they get their dns settings from the main router.
Also been trying 34578 and i encountered the exact same issue as 34777. Did not test other intermediary builds apart from these.
Router: DIR-615e3
Firmware: dir615e3-firmware.bin (v3.0-r34777 std)
Kernel: Linux 3.10.108-dd #48303 Wed Jan 31 04:38:22 CET 2018 mips
Status: Buggy on gui
Reset: No
Notes on configuration:
DNSMasq
Virtual wireless with bridging x2
multiple DHCP server
QOS
Errors:
1. Apply settings on multiple pages does not work (for example Setup->Basic Setup, Setup->Network and Security->Firewall)
2. Firmware upgrade button does not work (I have had to use command line to upgrade/downgrade)
3. Factory Defaults (reset) does not work (apparently broken after 33006)
4. Firmware restore button broken (apparently broken after 33006)
5. Switch ports can not communicate with each other (see post https://www.dd-wrt.com/phpBB2/viewtopic.php?t=312371 ) [have not tested due to not using]
Router: DIR-825 rev B1
Firmware: dir825-firmware.bin (v3.0-r34777 std)
Kernel: Linux 3.10.108-dd #48285 Wed Jan 31 03:55:38 CET 2018 mips
Status: Working
Reset: No
Notes on configuration:
Media Network
DNSMasq
Port Forwarding
DHCP reservation
I am confused Port Forwarding is working for me... I have not added a new rule for a while. I have used all of those versions (except 34760). So that is strange to me.