408 Request Timeout
The server timed out waiting for the request. According to HTTP specifications: "The client did not produce a request within the time that the server was prepared to wait. The client MAY repeat the request without modifications at any later time.
Joined: 02 Aug 2017 Posts: 153 Location: Central Michigan
Posted: Mon Mar 05, 2018 19:24 Post subject:
Just flashed factory-to-dd-wrt no issues in my log. _________________ ISP: Charter
Modem: Netgear CM600
Router:(2) Asus RT-AC86U Merlin 384.5
Router: LinksysWRT3200Acm{RIP}
Router: Linksys EA8500 kongat r35030m (Vpn)
Router: Netgear X4S kongat r35965M
Vpn: IpVanish
Unbrick your 3200acm with usb to ttl cable: https://tinyurl.com/y9azvrkg
Installed r35244-2018.03.05 on my WRT1900ACS_v1 as a flash upgrade, keeping existing config. No issues for my config noticed yet, will report if find anything big.
Note: I'm not seeing the errors noted in other posts in my log (...XXX daemon.err httpd[1785]...). I have some warnings which I've always had for my OpenVPN server.
DD-WRT config reference for my WRT1900ACS_v1 (not vanilla, not overly complex): mostly wired devices ~75, mixed wireless mode + fixed channels using 5GHz & 2.4GHz @ 20MHz width ~20 clients, IPv6 on, OpenVPN server + segmented network, DHCP reservations for all known devices, access rules (internet block security cameras), port forwards, no QOS, firewall rules (OpenVPN & Guest), Guest 2.4GHz wifi segmented network
Joined: 02 Aug 2017 Posts: 153 Location: Central Michigan
Posted: Mon Mar 05, 2018 20:02 Post subject:
matth:: wrote:
Mark1958 wrote:
Just flashed factory-to-dd-wrt no issues in my log.
Do you have any customization made in your config?
Like routing, NAT, NAS, etc.
No but I always restore to factory defaults before flashing.
Mark _________________ ISP: Charter
Modem: Netgear CM600
Router:(2) Asus RT-AC86U Merlin 384.5
Router: LinksysWRT3200Acm{RIP}
Router: Linksys EA8500 kongat r35030m (Vpn)
Router: Netgear X4S kongat r35965M
Vpn: IpVanish
Unbrick your 3200acm with usb to ttl cable: https://tinyurl.com/y9azvrkg
Router/Version: Linksys WRT1900AC
Firmware: DD-WRT v3.0-r35244 std (03/05/18)
Kernel: Linux 4.9.86 #113 SMP PREEMPT Sun Mar 4 21:30:55 CET 2018 armv7
Previous: 34215
Mode/Status: AP / DHCP / DNS / uPnP / Gateway w/ PPPoE WAN and a DDNS enabled- All okay.
Reset: No
Issues/Errors: Signal is ~5% better.
Uptime:
Code:
root@wrt1900ac:~# date && uptime
Tue Mar 6 08:19:55 EST 2018
08:19:55 up 5:04, load average: 0.06, 0.04, 0.04
root@wrt1900ac:~#
_________________ Location (urban) - 1x Linksys EA8500 (AP wlan0 & wlan1 enabled)
1x Asus 68u (Repeater Bridge w/VAP) - wl0 disabled
1x Asus 87u (Client Bridge) - wl1 disabled
Latest and greatest builds
Last edited by stephensuley on Tue Mar 06, 2018 13:32; edited 1 time in total
Upgraded WRT3200ACM from prior version, NO reset. I'm not seeing the above mentioned log issues. Now seeing the best wan speed yet. Upgraded a short time ago and best I could tell nothing new is broke, will post back it if any new issues are discovered
I purchased my router on April 11, 2017 so my router should be able to be flashed. I read that WRT3200ACM routers manufactured after September 2017 may not be flashable.
Is anyone having this problem? A solution would be appreciated.
I purchased my router on April 11, 2017 so my router should be able to be flashed. I read that WRT3200ACM routers manufactured after September 2017 may not be flashable.
Is anyone having this problem? A solution would be appreciated.
When using this build on my WRT3200ACM, I can't use DNSSEC. I get nothing but 'Bad DNS config' errors. If I turn off the options, then I have good internet traffic, but enabling them again shuts down my internet. Anyone else seeing this? _________________ NETGEAR R9000 DD-WRT v3.0-r45192 std (12/29/20) (ROUTER)
NETGEAR ORBI Stock FW V2.7.2.102 (MESH)
WRT3200ACM (BS Build Usually) (BACKUP)
