Router: Netgear R7000
Firmware: DD-WRT v3.0-r35550M kongac (03/28/2018)
Kernel: Linux 4.4.124 #548 SMP Wed Mar 28 09:52:34 CEST 2018 armv7l
Status: Working
Reset: Yes. ddup --flash-latest + erase nvram
Errors: Yes, memory leak when Radio scheduling turns radio off
Hi,
first timer on DD-WRT. I have enabled Radio scheduling, and memory leak starts when radio is turned off. Consequence is router to hang cutting WAN access. Leak takes more than an hour and less than 2 hours to consume free memory (starting at 85% free). I tested switching radio on for just an hour: once radio is turned off leak starts, and when radio is turned on memory is released to its initial level.
I first started with Kong's current stable version and I got the problem, so I tried with this test build and leak is still there.
Router: Netgear R6300v2
Firmware: DD-WRT v3.0-r35550M kongac (03/28/2018)
Kernel: Linux 4.4.124 #548 SMP Wed Mar 28 09:52:34 CEST 2018 armv7l
Status: NG-reverted to prev version
Reset: No
Previous: 34320M
Errors: Yes, DNS not working. WAN IP flaps between 0.0.0.0 and expected address.
this is a DSLconnection for my folks IPv4 - reverting to 34320 (works fine)
Router: Netgear R8000
Firmware: DD-WRT v3.0-r35550M kongac (03/28/1
Kernel: Linux 4.4.124 #548 SMP Wed Mar 28 09:52:34 CEST 2018 armv7l
Status: DNSmasq rejecting ALL dns queries
Reset: No, dup --latest
Errors: DNSmasq is rejecting ALL DNS queries. I have removed all additional config options, removed IPTABLES rules, disabled firewall, turned DNSSEC off, used different static DNS servers... None of it restores DNS to DHCP clients. Ping to DNS servers works fine. Setting static DNS servers on clients works. Any client using the router (10.0.0.1) as DNS server cannot resolve hostnames. The router cannot resolve host names. The DNSmasq log is full of nothing but queries (and DHCP entires) with no response. dig says any query is REJECTED. Even the VPN can't resolve the hostname.
I'm at a loss here, tried everything except a reset at this point.
Router: Netgear R8000
Firmware: DD-WRT v3.0-r35550M kongac (03/28/18)
Kernel: Linux 4.4.124 #548 SMP Wed Mar 28 09:52:34 CEST 2018 armv7l
Status: DNSmasq rejecting ALL dns queries
Reset: No, dup --latest
Errors: DNSmasq is rejecting ALL DNS queries. I have removed all additional config options, removed IPTABLES rules, disabled firewall, turned DNSSEC off, used different static DNS servers... None of it restores DNS to DHCP clients. Ping to DNS servers works fine. Setting static DNS servers on clients works. Any client using the router (10.0.0.1) as DNS server cannot resolve hostnames. The router cannot resolve host names. The DNSmasq log is full of nothing but queries (and DHCP entires) with no response. dig says any query is REJECTED. Even the VPN can't resolve the hostname.
I'm at a loss here, tried everything except a reset at this point.
Sometimes bad/old nvram values can cause strange issues to newer builds, so this is what I do...
BEFORE I made the jump from (older) Build 33770M to (newer)355530M, I 1st documented my WORKING configuration via screen-shots and copying settings/scipts to a file to a PC and also made a nvram backup for the working Build 33770M to ONLY be used to restore only Build 33770M if the new build doesn't work out. I then updated the firmware waited about 2min after bootup and pressed and held the rest-button unit the power LED changed colour. After the next boot-up I logged-in and did Factory Defaults too. After bootup I manually configure the router to my saved documents and files. I been running on this NEW Build for 2 weeks.
But if the NEW build didn't work out for me, no problem reload Build 33770M and reload the nvram backup for Build 33770M and I'm back up again. _________________ Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9
Off Site 1
R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4
Off Site 2
R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531
Router: Netgear R8000
Firmware: DD-WRT v3.0-r35550M kongac (03/28/1
Kernel: Linux 4.4.124 #548 SMP Wed Mar 28 09:52:34 CEST 2018 armv7l
Status: DNSmasq rejecting ALL dns queries
Reset: No, dup --latest
Errors: DNSmasq is rejecting ALL DNS queries. I have removed all additional config options, removed IPTABLES rules, disabled firewall, turned DNSSEC off, used different static DNS servers... None of it restores DNS to DHCP clients. Ping to DNS servers works fine. Setting static DNS servers on clients works. Any client using the router (10.0.0.1) as DNS server cannot resolve hostnames. The router cannot resolve host names. The DNSmasq log is full of nothing but queries (and DHCP entires) with no response. dig says any query is REJECTED. Even the VPN can't resolve the hostname.
I'm at a loss here, tried everything except a reset at this point.
Sometimes bad/old nvram values can cause strange issues to newer builds, so this is what I do...
BEFORE I made the jump from (older) Build 33770M to (newer)355530M, I 1st documented my WORKING configuration via screen-shots and copying settings/scipts to a file to a PC and also made a nvram backup for the working Build 33770M to ONLY be used to restore only Build 33770M if the new build doesn't work out. I then updated the firmware waited about 2min after bootup and pressed and held the rest-button unit the power LED changed colour. After the next boot-up I logged-in and did Factory Defaults too. After bootup I manually configure the router to my saved documents and files. I been running on this NEW Build for 2 weeks.
But if the NEW build didn't work out for me, no problem reload Build 33770M and reload the nvram backup for Build 33770M and I'm back up again.
Do the same thing for prep. But I try it without a reset first just to see.
It’s working now. I rearranged the order of the additional config entries for DNSmasq and it started working. Which is odd. Whatever it was it’s working now. No reset needed. Very strange, never had an issue with the order of options before.
Ran into a new problem with the Gateway R7000 with over 15 days uptime. The GUI would not load up correctly with a lot of missing data, menu tabs where not labeled. I was able to get into other menus but all had a lot of missing information. I tried a couple of methods to reset httpd service with the same problem, only fix was reboot. I will see if the problem comes back. I still get daemon.err httpd[1323]: Request Error Code 401: Authorization required. please note that the default username is "root" in all newer releases every time I login. Even with the GUI issue all other services where working fine: DNSCrypt, OpenVPN, IPv6, YAMon3, etc... _________________ Home Network on Telus 1Gb PureFibre - 10GbE Copper Backbone
2x R7800 - Gateway & WiFi & 3xWireGuard - DDWRT r53562 Std k4.9
Off Site 1
R7000 - Gateway & WiFi & WireGuard - DDWRT r54517 Std
E3000 - Station Bridge - DDWRT r49626 Mega K4.4
Off Site 2
R7000 - Gateway & WiFi - DDWRT r54517 Std
E2000 - Wired ISP IPTV PVR Blocker - DDWRT r35531
got a very specific problem here, i had a powerloss and after that, the router was very weird, unstable ( cable or wireless ).
A normal reboot command solved all issues.
Router Model
Asus RT-AC56U
Firmware Version
DD-WRT v3.0-r35550M kongac (03/28/1
Kernel Version
Linux 4.4.124 #548 SMP Wed Mar 28 09:52:34 CEST 2018 armv7l
Reboot with factory defaults: YES
Working with LED issues. The LAN led never comes on. The 5Ghz led comes on even though I have it disabled. If this is an old issue... sorry, I have been away for awhile. If there is a workaround, please post a link. TNX
I've been on this since it came out and I've been noticing that my wifi drops and comes back regularly. For example, my phone will show an exclamation mark on the wifi symbol, then go to 4G, then quickly back to wifi every hour or so. Any ideas? This wasn't an issue before.
Also, is this bad?
Router Name R8000
Router Model Netgear R8000
Firmware Version DD-WRT v3.0-r35550M kongac (03/28/1
Kernel Version Linux 4.4.124 #548 SMP Wed Mar 28 09:52:34 CEST 2018 armv7l
Hostname R8000
Current Time Thu, 03 May 2018 11:51:45