Please report your feedback on this build release on Broadcom units:
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:
Note:
This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 29440_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.
_________________ _________________ ASUS GT-BE98 PRO Main: Fiber 5gbps up/down
ASUS AXE16000: AI Mesh node
2 X ASUS RT-AX89X: AI Mesh nodes
QNAP QSW-1208-8C 12-Port 10GbE Switch
XS712T ProSafe 12-Port 10GbE Switch
3 X R9000 DD-WRT Mesh
Posted: Sat May 12, 2018 7:37 Post subject: ASUS RT-AC68U & Linksys E2000
After a lot of WiFi and other issues, this build seeems to work for me, details:
Asus RT-AC68U
Firmware: DD-WRT v3.0-r35916 std (05/11/18) - (previous r35531 + tried build in between)
Kernel: Linux 4.4.131 #3073 SMP Mon May 7 08:49:26 CEST 2018 armv7l
5Ghz (Mixed) with 80Mhz channel width: Ok
SSH: Ok
Telnet: Disabled
Site Survey: Ok
Wi-viz Survey 2.4Ghz & 5Ghz: Ok
Reset: Yes
Status: Ok
Uptime: 15 min
CPU Temperature: CPU 65.5 °C / WL0 45.5 °C / WL1 45.5 °C
2 x E2000
Firmware: DD-WRT v3.0-r35916 mega (05/11/18) - (previous r35531)
Kernel: Linux 3.10.108-dd #19122 Fri May 11 18:24:52 CEST 2018 mips
2.4Ghz (NG-mixed) with 40Mhz channel width: Ok
SSH: Ok
Telnet: Disabled
Site Survey: Ok
Wi-viz Survey 2.4Ghz: Ok
Reset: Yes
Status: Ok
Uptime: 21 min
CPU Temperature: WL0 50.0 °C
All devices working as AP's each with individual 1Gb wired connections to main firewall
Joined: 26 Mar 2013 Posts: 1858 Location: Hung Hom, Hong Kong
Posted: Sat May 12, 2018 7:57 Post subject: Asus RT-N18U and DD-WRT BS build 35916
Router/Version: Asus RT-N18U
Firmware: DD-WRT v3.0-r35916 std (05/11/18)
Kernel: Linux 4.4.131 #3077 Fri May 11 13:32:40 CEST 2018 armv7l
Previous: DD-WRT v3.0-r35898 std (05/07/18)
Mode/Status: Access Point (AP), Wired Working
Reset: NO reset during firmware upgrade
Issues/Errors: no major problems, basic router
2. No LAN LEDs... all off though there were physical cables.
Miscellaneous:
- Router not using IPv6, VPN nor USB
- Router is NOT working 24/7
- WiFi broken in k3.x editions since build 35531? 5GHz problem?
Old problems:
a. DDNS (inadyn) crashed in build 31722
b. Testing port-forwarding via WAN IP from within LAN not working in builds 34411-34760. Needed external proxy server.
c. NTP client not working in builds 34886-34876,35034 (affecting process_monitor?)
d. The ping to www.google.com increased from 2ms to 13ms after setting a defunct
WINS server in Setup->Basic Setup->DHCP->WINS (also something related to blank Source Net?)
e. The "Source Net" field in Port-Forwarding screen displayd blank field as "¸ÖÁv",
from builds 32667 to 32767. Possibly null-pointer assignment?
f. Blank Source Net in Port Forwarding cripped WAN in builds 35831-35874! Needed to be "0.0.0.0/0" or no internet!
g. Running "cat /proc/mtd" in Administration -> Commands for builds before 35916 didn't escape HTML special characters.
speedtest.dd-wrt.35916.asus.rt-n18u.jpg
Description:
speedtest.net resultfor DD-WRT BrainSlayer build 35916 and Asus RT-N18U
Filesize:
9.18 KB
Viewed:
5600 Time(s)
_________________ Router: Asus RT-N18U (rev. A1)
Drink, Blink, Stretch! Live long and prosper! May the Force and farces be with you!
Posted: Sat May 12, 2018 11:01 Post subject: Buffalo D1800+D1300
Router: Buffalo WZR-D1800H
Firmware: DD-WRT v3.0-r35916 giga (05/11/18 )
Kernel: Linux 3.10.108-dd #19114 Fri May 11 18:16:43 CEST 2018 mips
Status: OK in CB-mode. Uptime ~1h.
Reset: no, previous r35531
Errors: see below
-wl0 and wl1 work again
-ntp does not work in CB-mode (works in AP-mode since r35898), so
still required. Will be fixed in r35920, introducing the same
-really wonder how r35910 could fix the k3x WiFi issues after r35531 for this router, as this was a change in config for zabbix (probably disabled on 90% and mine)... but what do I know.
-r35916 also working on D1300 (nearly same HW), CB. AC87 (AP) seems to work as well with r35916. _________________ 3xBuffalo WLI-H4-D1300
1xBuffalo WZR-D1800H
1xBuffalo WHR-HP-G300N
1xBuffalo WHR-1166D (stock f/w)
1xAsus RT-AC87U
1xAsus RT-AC88U
1xTP710
Joined: 08 May 2018 Posts: 14246 Location: Texas, USA
Posted: Sat May 12, 2018 14:19 Post subject:
Router: Linksys E4200
Firmware: DD-WRT v3.0-r35916 mega - 05/11/18
Kernel: Linux 3.10.108-dd #19122 Fri May 11 18:24:52 CEST 2018 mips
Status: OK
Reset: No
Errors: None so far, uptime is only about 15 minutes. 2.4 and 5GHz Radios working, TX/RX OK, no errors.
EDIT: Had to do a little config tweak to DNSMasq to pass ISP nameservers down (even though they are a fallback by default?) because Windows 10 1803 is a piece of sh*t.
EDIT#2: Disabled strict order resolution and set no-resolv with Google's nameserver IPs (no reboot on either 'fix', just 'apply settings'). There's gotta be some wonky issue with DNSMasq and Windows 10 v1803, it's even still showing the router IP and ISP nameserver IPs under connection properties...
Last edited by kernel-panic69 on Sat May 12, 2018 15:36; edited 2 times in total
still required. Will be fixed in r35920, introducing the same
-really wonder how r35910 could fix the k3x WiFi issues after r35531 for this router
My bad, I validated that test build 35910 fixed wireless, but ya it was actually r35905-r35907 that fixed it. I clarified the ticket and 35898 build thread; thanks!
Btw, you don't need the "stopservice process_monitor && " for the ntp workaround, since process_monitor never starts. Doesn't matter, I know, but saves a little nvram.
Router/Version: Netgear WNDR4000
Firmware: DD-WRT v3.0-r35916 mega ( 05/11/18 )
Kernel: Linux 3.10.108-dd #19122 Fri May 11 18:24:52 CEST 2018 mips
Mode: 2.4 GHz CB + 5 GHz AP & VAP
Issues: As @kooper2013 noted w/ ntp, to be fixed in the next build. Been up 30min now, but I've been running 35910 for a couple days w/ a wired laptop, wireless work laptop for VPN, and 2 Android 8 devices.
@mwchang, are sure your Update took? If you confirm, I'll let BS know that k4.4/ARM still has the issue.
My GUI Commands works now:
Joined: 18 Jul 2017 Posts: 45 Location: Wisconsin, USA
Posted: Sat May 12, 2018 15:22 Post subject: WiFi Works Again
Router/Version: Linksys EA6500 v1
Firmware: DD-WRT v3.0-r35916 giga ( 05/11/18 )
Kernel: Linux 3.10.108-dd #19106 Fri May 11 18:09:37 CEST 2018 mips
Previous: DD-WRT v3.0-r35531 giga ( 03/26/18 )
Mode/Status: Gateway/AP
Setup: Using IPv6 via DNSMasq, DDNS, & Port Range Forward.
Reset: No
Issues/Errors: None so far
Everything appears to be working normally. Great job Wifi devices connect normally _________________
Posted: Sat May 12, 2018 16:40 Post subject: Internet Connection Fails on Reboot
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r35916 std ( 05/11/18 )
Kernel: Linux 4.4.131 #3073 SMP Mon May 7 08:49:26 CEST 2018 armv7l
Previous: r32597 (technically stock Netgear, I went back to that for about a week)
Mode/Status: Gateway/AP
Reset: Yes
Issues/Errors: After the router reboots, it is unable to connect to the internet (internet light on router doesn't even turn on). WiFi works fine. In order to get the connection working again, I need to sign into the router and click "Apply Settings". After clicking this, the router is able to connect to the internet again.
EDIT: After some investigating,I was only able to recreate this when DNSEncrypt was enabled. Also, clicking Apply Settings stopped working this morning, so I was without internet until I tracked this down. I was using Cisco OpenDNS with DNSEncrypt. I didn't try any other providers. I've disabled DNSEncrypt for now.
Last edited by vegasgamer on Sun May 13, 2018 13:08; edited 5 times in total
Joined: 13 Aug 2013 Posts: 6870 Location: Romerike, Norway
Posted: Sat May 12, 2018 16:48 Post subject:
Router: Asus RT-AC66U
Firmware: DD-WRT v3.0-r35916 giga (05/11/1 Kernel: Linux 3.10.108-dd #19106 Fri May 11 18:09:37 CEST 2018 mips
Status: Working
Reset: no, previous r35531
Errors: Wifi is working in AP mode again.
Joined: 26 Mar 2013 Posts: 1858 Location: Hung Hom, Hong Kong
Posted: Sat May 12, 2018 18:44 Post subject:
jrscs wrote:
Router/Version: RT-AC66U A1
....
Issues/Errors: Yes, need the following command(s) for 5 Ghz connection and NTP time sync
sleep 5; stopservice lan; startservice lan;
sleep 15; ntpclient us.pool.ntp.org;
Router/Version: E4200 V1
.....
Issues/Errors: Yes, need the following command(s) for 5 Ghz connection and NTP time sync
sleep 5; stopservice lan; startservice lan;
sleep 15; ntpclient us.pool.ntp.org;
Smells like wrong timing to start services lan and ntpclient for the 5GHz radio in both routers... maybe a delayed start could avoid the problem?
_________________ Router: Asus RT-N18U (rev. A1)
Drink, Blink, Stretch! Live long and prosper! May the Force and farces be with you!
