FIRMWARE:OpenWrt SNAPSHOT r8217-2cc821e / LuCI Master (git-18.276.41146-280dd33) MODEM:ARRIS SURFBoard SB8200 ROUTER:Linksys WRT32X USB NAS:Western Digital BLACK 1 TB Hardrive + Startech USB 3.0 External SATA III Enclosure
I've been using r35916 on my Linksys WRT1900ACS v2 for a couple of hours and it's worked well. I have ~35 devices, mostly wireless and some wired. I run an OpenVPN client (I'll get sporty someday and run a server as well). My cable connection is 100 Mbs down and 100 Mbps up and I'm getting that performance or better when measured with Ookla Speedtest or measured by my wireless Xbox. Wireless speeds measured using iperf3 are ~500 Mbs.
Hopefully it is stable without reboots but I'll give it more time before I judge that aspect. _________________ FIRMWARE: 6-20-2018 - r36168
MODEM: ARRIS SURFBoard SB6183
ROUTER: Linksys WRT1900ACS V2
ISP: TWC Spectrum 100 Mbps Download | 10 Mbps Upload
SERVICES: IVPN OpenVPN Client
Linksys WRT3200ACM
Firmware Version: DD-WRT v3.0-r35916 std (05/11/1Cool
Kernel Version Linux 4.9.99 #142 SMP PREEMPT Wed May 9 12:15:51 CEST 2018 armv7l
Current TimeSat, 12 May 2018 19:07:17
Uptime 7:07
installed after reset from openwrt, then restored nvram from backaup from last version
no problems to so far
gateway, 3 wifi radios, >30 devices, 100mbs wan, htb/sfq qos working well.
i have been following all the bad stories about the wrt3200acm, but with recent open wrt and dd-wrt builds, things seem pretty good.
thanks to devs and contibutors.
Installed r35916-2018.05.11 on my WRT1900ACS_v1 as flash upgrade without issues. So far everything seems to be working in my config, will post/update if I find anything.
DD-WRT config reference for my WRT1900ACS_v1 (not vanilla, not overly complex): mostly wired devices ~75, wireless using 5GHz-AC Only & 2.4GHz-Mixed both @ 20MHz width non-overlapping channels (also have 2 APs in house) w/ ~20 clients, IPv6 on, DHCP reservations for all known devices, access rules (internet block security cameras), port forwards, no QOS, running OpenVPN server, firewall rules (OpenVPN & Guest), Guest 2.4GHz wifi segmented network/dhcp
_________________
Router: Linksys WRT1900ACS_v1
Firmware: DD-WRT v3.0-r35916 std 05/11/18
Cable Modem: Motorola MB7420
ISP: Comcast
Speed Test: http://www.dslreports.com/speedtest/33323500
how did you guys get this working on WRT1900ACS V2? In the last 2 builds it seems it will just bootloop on my router.
Flashed from the Lastest Linksys Firmware and then it wil just bootloop until it boots back to the UI firmware again. 4/6/2018 build seems flashing just fine, any idea?
Switched to Linksys firmware...
(In Admin/Commands)...
ubootenv set boot_part 1
(If Linksys is on 1)..
reboot
Once back in Linksys firmware just use the
firmware upgrade installing the
factory-to-ddwrt.bin
Reboots back to the DDwrt partition with the new version. Then restore your settings.
This has never failed to work on my WRT1900ACSv2.
However there are issues with the DD-WRT releases in the past few months. Of course if you don't use any of the broken features then it's not an issue.
They're all betas so which ever builds work for your
configuration/requirements.