Posted: Wed Nov 22, 2023 6:22 Post subject: New Build - 11/21/2023 - r54095
Welcome to Atheros r54095 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Router/Version: TP-Link TL-WR841ND v10
File/Kernel: DD-WRT v3.0-r54095 std (11/22/23) / Linux 3.18.140-d6 #185219 Wed Nov 22 06:45:34 +06 2023 mips
Previous/Reset: r54079 / no reset
Mode/Status: WDS Station with network mode "N / G mixed" and channel width "Full (20 MHz)" | no connection to WDS AP after update
Issues/Errors: Because of no connection to WDS AP i found this in syslog on WDS Station => [wpa_supplicant] : Error on startup, returncode 255
Reverted to r54079 and checked how wpa_supplicant is running. Saved content of "/tmp/wlan0_wpa_supplicant.conf" and reupdated device to r54095. Compared configs and in new version was this additional line:
disable_he=1
Removed this line and tried to start wpa_supplicant. This time the service could be started and connect to WDS AP. For testing, i stopped the service again, readded the line and service won't start anymore. Without that line the service starts.
Joined: 16 Nov 2015 Posts: 6447 Location: UK, London, just across the river..
Posted: Wed Nov 22, 2023 19:19 Post subject:
Router Model TP-Link WR1043ND V2
Firmware Version DD-WRT v3.0-r54095 std (11/22/23)
Kernel Version Linux 3.18.140-d6 #185233 Wed Nov 22 07:04:17 +06 2023 mips
update: GUI r53833 > r54095
reset: NO
mode: Gateway
status: Operational 2h+
errors: Nothing new, yet...Thanks BS and Team ! _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
My newly purchased Netgear XR500 Pro arrived today.
Flashed via GUI from DumasOS to DD-WRT r54095 - felt like living dangerously.
Eventually the DD-WRT initial screen came up - by then I'd lost most of my fingernails.
It didn't like it initially - ethernet/initial screen dropped out several times and I thought I'd got it into a boot loop.
Eventually it settled.
I flashed it again (with reset) to do the second partition.
It came back up eventually, and I proceeded to set it up as my main Gateway.
It's a very basic setup - 2.4GHz and 5GHz wifi with WPA2/3.
Been up for 2 hours - so far so good.
Only issue is the Internet LED is not lit up.
Will tweak it further later.
Might also try and boot into other partition and see what happens.
I also purchased a secondhand Netgear XR1000 - that one will stay on DumasOS.
EDIT:
Decided to try out 2nd partition on XR500 by 3x reboot method.
Result: it goes back to r54095 already setup, rather than the other non-setup partition.
So it appears that I'm working without a net again. _________________ ------------------------------------
Linksys WRT3200ACM DD-WRT r56029 (Gateway)
Linksys EA8500 OpenWrt-23.05.3 (Wired AP)
Netgear WNDR3700v4 DD-WRT r55819 (spare Gateway)
Photos: https://www.flickr.com/photos/nickant44/albums
Joined: 18 Mar 2014 Posts: 12923 Location: Netherlands
Posted: Thu Nov 23, 2023 7:16 Post subject:
nickant wrote:
My newly purchased Netgear XR500 Pro arrived today.
Flashed via GUI from DumasOS to DD-WRT r54095 - felt like living dangerously.
Eventually the DD-WRT initial screen came up - by then I'd lost most of my fingernails.
It didn't like it initially - ethernet/initial screen dropped out several times and I thought I'd got it into a boot loop.
Eventually it settled.
I flashed it again (with reset) to do the second partition.
It came back up eventually, and I proceeded to set it up as my main Gateway.
It's a very basic setup - 2.4GHz and 5GHz wifi with WPA2/3.
Been up for 2 hours - so far so good.
Only issue is the Internet LED is not lit up.
Will tweak it further later.
Might also try and boot into other partition and see what happens.
I also purchased a secondhand Netgear XR1000 - that one will stay on DumasOS.
Are you sure the XR500 is dual partition?
Choosing reset while upgrading is not recommended there is a slight chance of bricking, better reset after update.
I tried to reboot 3x to swap partitions but it went back to original one.
(see my Edit, just b4 you posted)
I assumed XR500 was dual partition, as R7800/EA8500 used to be - same chipset family.
Can someone clarify if this is the case or not? _________________ ------------------------------------
Linksys WRT3200ACM DD-WRT r56029 (Gateway)
Linksys EA8500 OpenWrt-23.05.3 (Wired AP)
Netgear WNDR3700v4 DD-WRT r55819 (spare Gateway)
Photos: https://www.flickr.com/photos/nickant44/albums
Posted: Sat Nov 25, 2023 12:07 Post subject: wifi Station mode not working after build 54079
I have TL-WA901nd-V3(setup as a repeater) and after I updated to r54095 or r54109, I see that it cannot connect to the wifi network I configured(Station mode). I also have virtual wlan interface in AP mode which appears to work correctly. I haven't tryed erasing the nvram while upgrading.
