Posted: Fri Feb 02, 2024 15:19 Post subject: New Build - 02/02/2024 - r55052
Welcome to Broadcom r55052 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Router/Version: Asus RT-AC87U R
Update method: WebUpgrade
File/Kernel: asus_rt-ac87u-firmware.trx_r55052 std / Linux 4.4.302-st48 #10953 SMP Fri Feb 2 06:15:14 +06 2024 armv7l
Previous/Reset: r55033 / no
Mode/Status: Gateway / Up and running for 2:05 hours
CPU Temperature: CPU 62.5 °C / WL0 40.5 °C / WL1 0.0 °C (ambient temperature 17.0 °C)
Issues/Errors: Nothing significant
As always, the Quantenna chip has its own quirks. This is a closed source chipset
There is no way to install a channel.
But you can disable 5.0 GHz. @mpgalaxy hack "If you set the radio mode to station bridge and disable the network mode, the 5GHz device will turn off completely even after reboot."
The fact is that the router is connected to the Internet (to the Internet provider). And it reports an error, the red WAN indicator flashes (the icon in the form of a planet). The internet works, I just think it's a glitch.
But this does not affect the work.
Just relax
CPU temperature readings started changing after one second from 61.9 - 62.5 °C
Thank you BS and gurus! _________________ Atheros
Netgear XR500 Nighthawk - DD-WRT 54545
Tp-Link TL-WDR4900 v1.3 - DD-WRT 53133
TP-Link WR1043ND v4 - DD-WRT 51838
TP-Link WR1043ND v2 - Gargoyle OS 1.13.0
TP-Link WR841ND v11 - DD-WRT 56029
Broadcom
Asus RT-AC87U R - DD-WRT 56029
Asus RT-N66U - DD-WRT 55819
Linksys WRT54GL v1.1 - DD-WRT 54517M
Linksys WRT54GL v1.1 - FreshTomato 2023.4_MIPS_K26
Linksys WRT54GL v1.1 - Gargoyle OS 1.6.2
Joined: 16 Nov 2015 Posts: 6447 Location: UK, London, just across the river..
Posted: Sat Feb 03, 2024 14:53 Post subject:
Router Model Netgear R7000
Firmware Version DD-WRT v3.0-r55052 std (02/02/24)
Kernel Version Linux 4.4.302-st48 #10945 SMP Tue Jan 30 10:55:44 +06 2024 armv7l
update: CLI r55009 > r55052
reset: NO
mode: Gateway/SmartDNS, AD-Block(via script), Firewall,Forced DNS,AP&Net Isolation,x3VLAN,VPN client(PBR),40 HT 2.4Ghz only
status: Operational 24h+
errors: Nothing new, yet...Thanks BS and Team ! _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Have anyone tested if the port forwarding issue reported in build 55009 is resolved in this build? _________________ Netgear R7000 on Build 55109
Asus AC-AC68U rev. C1 (AP) on Build 55109
Asus AC-68U rev. A1 on Build 54604
Asus AC-68U rev. A1 on Build 53339
Joined: 26 Mar 2013 Posts: 1858 Location: Hung Hom, Hong Kong
Posted: Mon Feb 05, 2024 12:14 Post subject: DD-WRT BS build 55052 and Asus RT-N18U
Router/Version:Asus RT-N18U (rev. A1)
Firmware: DD-WRT v3.0-r55052 std (02/02/24)
Kernel: Linux rt-n18u-hst 4.4.302-st48 #10949 Fri Feb 2 05:44:48 +06 2024 armv7l DD-WRT
Previous: DD-WRT v3.0-r54637 std (12/29/23)
Mode: WAN @ DHCP, Wireless @ AP (Mixed)
Status: Core functions Working {
Not 24/7; Not using CTF, FA, STP, IPv6, VPN, VAP;
USB storage(/jffs, /opt); NAS (lighttpd);
Cron enabled(default jobs deleted);
WAN DNS disabled; DDNS (no-ip.com) In-a-Dyn OK;
DNSmasq not serving DNS; Recursive DNS Unbound (/jffs/etc/unbound.conf);
Entware core (CPU: armv71) installed without problem;
Swap partition (USB) enabled for using GitHub
}
Reset: NO RESET (using command not WEBUI to flash; httpd disabled)
File:https://download1.dd-wrt.com/dd-wrtv2/downloads/betas/2024/02-02-2024-r55052/asus-rt-n18u/
Summary
On *SECOND* reboot after flashing this build (1st boot is old->new, 2nd boot is new->new), the router lost all WAN and LAN connections. Later, I rebooted this new build, it again caused the router to lose all network connections.
Other than ksmbd, everything was working fine after COLD boot (power off->on).
I had ksmbd disabled in the WEBUI and manually started it after init. ksmbd worked for about 50 seconds, then it stalled and could NOT be killed nor restarted. The command to stop ksmbd ("sh -c echo hard > /sys/class/ksmbd-control/kill_server") also failed and didn't respond.
Without ksmbd.control in ksmbd-tools, it's difficult to provide more information.
Router/Version: TP-Link Archer C9 v1
File/Kernel: renamed archer-c9v1-webflash.bin to the latest TP-Link OEM firmware c9v1_un-up-ver4-1-0-P31[20160517-rel35411].bin Previous/Reset: DD-WRT r44715/no reset
Mode/Status: AP
Issues/Errors: none
I managed to update my C9v1 to latest DD-WRT release and this method will work from now on, for all future updates:
The trick:
- I renamed archer-c9v1-webflash.bin to the latest TP-Link OEM firmware c9v1_un-up-ver4-1-0-P31[20160517-rel35411].bin
- uploaded and flashed from DD-WRT web interface
- magic happened
Router/Version: Asus RT-N66U
Update method: WebUpgrade
File/Kernel: dd-wrt.v24-r55052_NEWD-2_K3.x-big-RT-N66U.trx / Linux 4.4.302-st48 #28395 Fri Feb 2 06:49:03 +06 2024 mips
Previous/Reset: r55033 / no
Mode/Status: Gateway / Up and running for 1 days, 2:11
CPU Temperature: WL0 48.5 °C (ambient temperature 20.3 °C)
Issues/Errors: Nothing significant
CPU temperature readings started changing after one second from 48.0 - 48.5 °C
Thank you BS and gurus! _________________ Atheros
Netgear XR500 Nighthawk - DD-WRT 54545
Tp-Link TL-WDR4900 v1.3 - DD-WRT 53133
TP-Link WR1043ND v4 - DD-WRT 51838
TP-Link WR1043ND v2 - Gargoyle OS 1.13.0
TP-Link WR841ND v11 - DD-WRT 56029
Broadcom
Asus RT-AC87U R - DD-WRT 56029
Asus RT-N66U - DD-WRT 55819
Linksys WRT54GL v1.1 - DD-WRT 54517M
Linksys WRT54GL v1.1 - FreshTomato 2023.4_MIPS_K26
Linksys WRT54GL v1.1 - Gargoyle OS 1.6.2
Router/Version: TP-Link Archer C9 v1
File/Kernel: DD-WRT v3.0-r55052 std (02/02/24) / Linux 4.4.302-st48 #10947 SMP Fri Feb 2 05:36:11 +06 2024 armv7l
Mode: Gateway/AP, CTF+FA, DNSMasq DHCP v4 & v6 SLAAC+RA, SmartDNS, SMB, DDNS
Previous/Reset: 54682 / No reset, WebUI
Status: Crash on USB SMB access, reverted to 54682. Core networking functions seem OK.
Issues/Errors:
Accessing EXT4 USB via SMB works briefly, then causes the router to crash and restart. Works OK on 54682.
A few speedtest runs suggest 55052 is also performing poorly compared to 54682.
Joined: 26 Mar 2013 Posts: 1858 Location: Hung Hom, Hong Kong
Posted: Sun Feb 11, 2024 6:22 Post subject:
Today I found my router not responding to usual SSH connection. I assumed that it's been compromised (well I did NOT bother to find out the truth). So I reset it. That did NOT solve the ksmbd problem, and it still stalled after some time.
Lastly, I took this chance to go back to build 54682.
End of report.
Postscript: it could just have been an USB error. Well... _________________ Router: Asus RT-N18U (rev. A1)
Drink, Blink, Stretch! Live long and prosper! May the Force and farces be with you!
