eoc 5610 flashing problem from firmware 1.1.12

Post new topic   Reply to topic    DD-WRT Forum Index -> Senao Devices
Author Message
bayoule
DD-WRT Novice


Joined: 22 Sep 2009
Posts: 7

PostPosted: Mon Oct 26, 2009 15:10    Post subject: eoc 5610 flashing problem from firmware 1.1.12 Reply with quote
Hi,

Like to buy an activation password. So I followed the prcedure to first try. It wouldn't load the linux.bin file error after 94% using Tftp32. I got:

About to initialize [format] FLASH image system - continue (y/n)? y
*** Initialize FLASH Image System
... Erase from 0xbe7e0000-0xbe7f0000: .
... Program from 0x81fe0400-0x81ff0400 at 0xbe7e0000: .

The numbers are quite different from the ones in the stickys. I am upgrading from 1.1.12. Brainslayer, Sash, any idea? The LAN led works well and I can boot redboot. Just can't have it to loa the bin file?
Any idea?
Thanks
Sponsor
MichelG
DD-WRT Guru


Joined: 12 Feb 2007
Posts: 903
Location: Galati - RO / Kishinev - MD / Geneva - CH / Tarragona - E

PostPosted: Mon Oct 26, 2009 17:30    Post subject: Reply with quote
Hi, did you follow the procedure till the end ? It also takes around 10-15 minutes to have it done, so dont interrupt the transfer at that moment. JUST WAIT !

Also, which version are you trying to load ? I had to load the 13064 twice, in order to have it working.

Cheers, Michel

_________________
2x EOC-2160 - AP 2x14dB Yagy to 450m link
2x EOC-2160 - RP 2x17dB Panels - 2x 7Mbps
1x WRT54G v2.2 - V24-SP2 13577VPN Eko
All Senao EOC-2610 V1.10 Std 15362 BS
1x UBNT Bullet 2 - RP 18dB Panel - 11Mbps - 13Km link
bayoule
DD-WRT Novice


Joined: 22 Sep 2009
Posts: 7

PostPosted: Mon Oct 26, 2009 18:23    Post subject: Reply with quote
Yes I waited till I saw ERR in tftpd32? I was loading the latest from 09/10/10
Regards
Bayoule
bayoule
DD-WRT Novice


Joined: 22 Sep 2009
Posts: 7

PostPosted: Mon Oct 26, 2009 18:34    Post subject: Reply with quote
Also I am not an expert and I might be totally wrong but it seems as if there was not enough space in memory to write the file, as if it starting to close to the end (again those numbers)?
Bayoule
MichelG
DD-WRT Guru


Joined: 12 Feb 2007
Posts: 903
Location: Galati - RO / Kishinev - MD / Geneva - CH / Tarragona - E

PostPosted: Mon Oct 26, 2009 19:28    Post subject: Reply with quote
Check your RJ-45 cable and connectors. Also, it might be an issue related to stability of your power supply, or of a switch / hub if do use one.

Check that,

_________________
2x EOC-2160 - AP 2x14dB Yagy to 450m link
2x EOC-2160 - RP 2x17dB Panels - 2x 7Mbps
1x WRT54G v2.2 - V24-SP2 13577VPN Eko
All Senao EOC-2610 V1.10 Std 15362 BS
1x UBNT Bullet 2 - RP 18dB Panel - 11Mbps - 13Km link
bayoule
DD-WRT Novice


Joined: 22 Sep 2009
Posts: 7

PostPosted: Wed Oct 28, 2009 21:21    Post subject: Reply with quote
OK,

Coming back after checking power and chnging cables. Still not loading. Is this 15mn for loading or for fis create linux cos mine simply not loading? Any other ideas? Thanks
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17619
Location: Hesse/Germany

PostPosted: Thu Oct 29, 2009 9:20    Post subject: Reply with quote
disable firewalls, put a switch between pc and eoc, use an other tftp server
_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
techtravis
DD-WRT Novice


Joined: 10 Aug 2009
Posts: 42
Location: Michigan, USA

PostPosted: Fri Oct 30, 2009 2:15    Post subject: Reply with quote
Same exact issue. EOC-5610 locks up at 94% download.

same memory values too

About to initialize [format] FLASH image system - continue (y/n)? y
*** Initialize FLASH Image System
... Erase from 0xbe7e0000-0xbe7f0000: .
... Program from 0x81fe0400-0x81ff0400 at 0xbe7e0000: .


Are we sure load -r -b 0x80041000 linux.bin is the right command... could the starting memory location be different?

I should mention my beginning firware was 1.1.07 and not 1.1.12 as the original posters was.

_________________
EOC-5610 -dd-wrt soon....
WRT54g-tm -Mega Build
WRT350n -Mega Build, w/ ext antennas
techtravis
DD-WRT Novice


Joined: 10 Aug 2009
Posts: 42
Location: Michigan, USA

PostPosted: Fri Oct 30, 2009 2:32    Post subject: Reply with quote
after a little bit of common sense....

Since build 13064 seemed to be a little too big. I looked at build 12533

build 12533 is roughly 2mb smaller than build 13064.

I followed the directions but this time used 12533, everything went off without a hitch!

Someone might want to look at the bin listed for the EOC-5610 it looks like build 13064 might be bad?

_________________
EOC-5610 -dd-wrt soon....
WRT54g-tm -Mega Build
WRT350n -Mega Build, w/ ext antennas
Sash
DD-WRT Guru


Joined: 20 Sep 2006
Posts: 17619
Location: Hesse/Germany

PostPosted: Fri Oct 30, 2009 9:58    Post subject: Reply with quote
techtravis wrote:

Someone might want to look at the bin listed for the EOC-5610 it looks like build 13064 might be bad?


this build works ok!
maybe your tftp has problems with the size

_________________
Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search Exclamation
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
bayoule
DD-WRT Novice


Joined: 22 Sep 2009
Posts: 7

PostPosted: Tue Nov 03, 2009 22:19    Post subject: Reply with quote
OK I was able to load 12533 like Techtravis. I bought the activation code too. Now I am afraid to upgrade through web for 13064? Should I wait for the next release? Thanks
Bayoule
GeeTek
DD-WRT Guru


Joined: 06 Jun 2006
Posts: 3763
Location: I'm the one on the plate.

PostPosted: Tue Nov 03, 2009 22:48    Post subject: Reply with quote
bayoule wrote:
OK I was able to load 12533 like Techtravis. I bought the activation code too. Now I am afraid to upgrade through web for 13064? Should I wait for the next release? Thanks
Bayoule

Is there a particular reason for your burning desire to stay at the cutting edge of this beta firmware development and endure the punishment of on-going de-bugging ?

Is there a specific feature or functinality in the newest revision that you are after ? I would love to know.
bayoule
DD-WRT Novice


Joined: 22 Sep 2009
Posts: 7

PostPosted: Wed Nov 04, 2009 6:38    Post subject: Reply with quote
Not really just assumes that newer version are fixing bugs as opposed to regress.
Cheers
Bayoule
techtravis
DD-WRT Novice


Joined: 10 Aug 2009
Posts: 42
Location: Michigan, USA

PostPosted: Wed Nov 04, 2009 6:49    Post subject: Reply with quote
In retrospect I wish I hadn't upgraded :)

I know if the next router has the same symptoms (will load 12533 and not 13064 through redboot) I won't even attempt 13064.

It wouldn't be sure a big deal if they included a JTAG port on the damn thing.

_________________
EOC-5610 -dd-wrt soon....
WRT54g-tm -Mega Build
WRT350n -Mega Build, w/ ext antennas
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Senao Devices All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum