Serial port pinouts
From DD-WRT Wiki
Revision as of 04:00, 8 June 2009 (edit) Jjohnsonphx (Talk | contribs) (→Buffalo WHR-HP-G54) ← Previous diff |
Revision as of 22:00, 10 October 2009 (edit) (undo) Borice (Talk | contribs) (- added pinout for DYNEX DX-NRUTER wireless N router) Next diff → |
||
Line 103: | Line 103: | ||
==Airlink AR430W== | ==Airlink AR430W== | ||
[[Image:Ar430wserial.jpg]] | [[Image:Ar430wserial.jpg]] | ||
+ | |||
+ | ==Dynex DX-NRUTER== | ||
+ | [[Image:dynex_nruter.png]] | ||
+ | |||
==External Links== | ==External Links== | ||
*[http://www.dd-wrt.com/phpBB2/viewtopic.php?t=12879 Original source of this page on the DD-WRT forums] | *[http://www.dd-wrt.com/phpBB2/viewtopic.php?t=12879 Original source of this page on the DD-WRT forums] |
Revision as of 22:00, 10 October 2009
If anyone has any photos or diagrams, please upload them to the wiki (NOT link to an external image) and add them to this page.
Contents |
For those interested: (--------- is nearest board edge)
Buffalo WBR2-G54(S)
---------- J5 o gnd o vcc o rx o tx
Motorola WR850G v2 /v3
| tx o o vcc RJP1 | o o | o o gnd | rx o o | o
Buffalo WLA2-G54C
| tx o o | o o vcc | o o gnd | rx o o | o ---------
Buffalo WHR-G54S
Connector RJP1
tx o o | o o vcc | o o gnd | rx o o | o | -------------
The serial port runs at 115200 baud, 8 bits, no parity, 1 stop bit using ANSI terminal emulation.
Buffalo WHR-HP-G54
Connector J1
| rx o | tx o | gnd o | vcc o | -------------
The serial port runs at 115200 baud, 8 bits, no parity, 1 stop bit using ANSI terminal emulation. Levels are not RS232 voltage levels, but +3.3V TTL logic. Use level shifter (Max232/Max3232/DS275 etc.) to correct this. Also a USB to serial phone cable will work in most cases. A cable with a Prolific 2303 works fine.
Buffalo WHR-G125
Connector J1
| | rx o | tx o | gnd o | vcc o -------------
The serial port runs at 115200 baud, 8 bits, no parity, 1 stop bit using ANSI terminal emulation. Levels are not RS232 voltage levels, but +3.3V TTL logic. Use level shifter (Max232/Max3232/DS275 etc.) to correct this. Also a USB to serial phone cable will work in most cases. A cable with a Prolific 2303 works fine.
Linksys WRT-54G(S,L)
JP1 or JP2 (on newer models)
vcc 1-2 vcc |
tx1 3-4 tx0 |
rx1 5-6 rx0 |
... 7-8 ... |
gnd 9-10 gnd |
(numbering as shown on the PCB at JP2 in my WRT54GL v1.1, Rockus 10:42, 25 May 2008 (CEST))
below numbering shown on my WRT-54GS V1 with JP1 busstopgangsta 11.11.2008 00:16 GMT+1
Linksys WRT-350N v 2.0
J5
vcc o tx1 o rx1 o gnd o
Asus WL-500 deluxe
| o o | gnd o o vcc | tx1 o o tx0 | rx1 o o rx0 | J5
Sparklan WX6615GT
| o | gnd o o rx | gnd o o | vcc o o | vcc o o tx | J5