From DD-WRT Wiki

Revision as of 17:44, 13 October 2005

Introduction

WDS creates a wireless backbone link between multiple access points that are part of the same wireless network. This allows a wireless network to be expanded using multiple access points without the need for a wired network connection to link them. The WDS-enabled access points can accept wireless clients (e.g. wireless laptop users) just as the main wired access point (or wireless router) does.

There is no free lunch, however: WDS consumes some wireless bandwidth normally available to wireless clients.

Current Status for DD-WRT

WDS does not work well currently on DD-WRT prefinal5. Use DD-WRT prefinal4 for the time being (5-13-2005).

DD-WRT v22 R2 seems to be working well.

DD-WRT v23 Beta 30092005 appears to work with WEP, WPA, & WPA2 set from the GUI (no work-around necessary).

Confirmed Working Products

-Apple Airport Express
-Linksys WRE54G Wireless Range Expander
-Belkin F5D7230-4  802.11g Wireless DSL/Cable Gateway Router
-Belkin F5D7231-4
-CompuShack SWA-103 (Waveline Micro AccessPoint) Repeater Mode
-Fujitsu Siemens AP-600RP

Installation

WDS Linking with WRT54GS

A pretty decent forum post was made about WDS Linking with WRT54GS.

Find it here: http://forum.bsr-clan.de/ftopic624.html

Original was here: http://www.linksysinfo.org/modules.php?name=Content&pa=showpage&pid=7 (with pictures)

Setting up WDS between a DD-WRT router and an Apple Airport Express

This has been tested with prefinal4 [6-15-05]

1) [Wireless->Basic Settings] Set the channel on the DD-WRT to 1
2a) [Wireless->WDS] Select "LAN" option and enter the airport express's AIRPORT id
2b) Set Lazy WDS and WDS subnet to disable
3) [Administration->Management] Set Loopback to disable
4) [Security->Firewall] Turn off "Block Anonymous Internet Requests"
5) Open Airport admin utility and find the new express, then double click it
6) In the airport tab:
   Select "Create Wireless Network"
   Set Network name to your wireless SSID
   Set the wireless channel to 1
7) WDS tab:
   Enable this base statio
   Set base station as "remote base station"
   In the Main Aiport ID section enter your DD-WRT wireless mac (can get this in status->wireless)
8) Click "update"

if it works then there will be a solid green light (may take a couple of minutes)

source: http://ryanschwartz.net/2004/08/05/airtunes-airport-express-and-the-wrt54g

Also make sure that you disable the "AP Watchdog" daemon. If you have a wireless endpoint (like a laptop) which connects to the Airport station (because you use WDS) then the Linksys does not see any Clients connected and restarts the wireless network over and over.

Also note that the above configuration with the Airport Express works with either no encryption or WEP encryption. When using WEP encryption, make sure you enter your WEP key into the Airport Express exactly how it is entered into the WRT54G 'BUT' add a $ to the beginning of the key.

WPA/WPA2 encryption does not appear to work over WDS (but will work when the Airport Express is configured in client mode - but in client mode, the RJ45 connection is not usable). The error that the WRT54G reports back when the Airport Express is trying to associate via WPA over WDS is: eapol_sup_dispatch wds0.49153: unknown EPOL type 3 . AFAIK, EPOL has to do with WPA, so perhaps if this issue can be resolved, then the two devices could associate.

You are here: Main Page/DD-WRT Doku (EN)/WDS Linked router network