stick to united states for reg domain for now, many countries such as haiti (for highest tx power) are broken & will cap ath9k routers to a much lower tx power.
not a thing changed since r31690..all critical issues remain. _________________ LATEST FIRMWARE(S)
BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers
Netgear WNDR3700 V4
DD-WRT v3.0-r31722 std (03/21/17)
Linux 3.18.48 #2587 Tue Mar 21 06:13:45 CET 2017 mips
working ok
--
Linksys EA8500
DD-WRT v3.0-r31722 std (03/21/17)
Linux 3.18.48 #131 SMP PREEMPT Fri Mar 17 01:22:47 CET 2017 armv7l
working ok --- but with TurboQAM enabled No clients can connect to ath0
http://svn.dd-wrt.com/ticket/5738
--
Linksys WRT160NL
DD-WRT v3.0-r31722 std (03/21/17)
Linux 3.10.105 #30268 Tue Mar 21 04:59:29 CET 2017 mips
working -
Will only install on wrt160NL or e2100L with flash id 0x1c2017 .
Will NOT install on wrt160NL or e2100L with flash id 0xc22017 .
http://svn.dd-wrt.com/ticket/5412#comment:31
Router: TPLINK WR1043ND V3
Firmware: DD-WRT v3.0-r31722 (03/21/17)
Kernel: Linux 3.18.48 #2571 Tue Mar 21 05:51:04 CET 2017 mips
Status: OK
Reset: 2x
Errors: None so far
Joined: 16 Nov 2015 Posts: 6447 Location: UK, London, just across the river..
Posted: Wed Mar 22, 2017 9:17 Post subject:
Router Model TPLINK WR1043ND V2
Firmware Version DD-WRT v3.0-r31722 std (03/21/17)
Kernel Version Linux 3.18.48 #2571 Tue Mar 21 05:51:04 CET 2017 mips
reset : x2
status: operational
errors: none so far... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 55630 WAP
TP-Link WR1043NDv2 -DD-WRT 55723 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 55779 Gateway/DoH,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 55819 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 55779 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 55460 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Router: DIR-615 i1
Status:Good Reset: Reset to defaults with flash procedure; erased NVRAM before and after flash
Errors: None
Router: TL-WDR3600 v. 1.5
Status:Good Reset: Reset to defaults with flash procedure; erased NVRAM before and after flash
Notes: 5 GHz LED not illuminating, but radio is working. r31690 was much more stable than r31571 on this router, as there were a few random crashes/reboots on r31571. Waiting to see how r31722 performs but in general, the random crashing and rebooting issue on the TL-WDR3600 appears to be just about fixed.
After flashing the firmware, the power led blinks 4s on, 1s off.
What does it mean? Do I have a doorstop now?
I'm trying to ping it, but it says destination unreachable / network unavailable (I'm translating here; not sure of the exact words)
systemd-networkd says lost carrier / gained carrier etc
The led continues to blink like that even during a 30/30/30
What can I do now? I'm using Arch Linux
EDIT: keeping the wps button pressed for a while I captured some arp packets from the router from 192.168.11.1. It is asking for firmware.ram via tftp
What firmware do I have to send it? Ddwrt uImage or the original buffalo firmware?
After flashing the firmware, the power led blinks 4s on, 1s off.
What does it mean? Do I have a doorstop now?
I'm trying to ping it, but it says destination unreachable / network unavailable (I'm translating here; not sure of the exact words)
systemd-networkd says lost carrier / gained carrier etc
The led continues to blink like that even during a 30/30/30
What can I do now? I'm using Arch Linux
EDIT: keeping the wps button pressed for a while I captured some arp packets from the router from 192.168.11.1. It is asking for firmware.ram via tftp
What firmware do I have to send it? Ddwrt uImage or the original buffalo firmware?
Buffalo routers are pretty hard to truly brick. If you attempted to update via web interface it might be in firmware recovery mode ( which it sounds like from your later statement ) there is a wiki on here that explains in good detail how to go about it. 2 things you will find handy if doing a tftp firmware flash from a windows computer are pumpkin tftp and a spare switch between the router and your windows computer.
Router Model: D-Link DIR-615-E3
Kernel Version: Linux 3.10.105 #30284
Status: (updated 3/28/2017) Errors found after few more days testing
Reset:No
Errors: Initially working great in standard Router/AP mode with mix of desktops and wireless. Recently discovered issue with certain wireless devices getting kicked out and not reconnecting, or needing manual reconnect. Syslog indicates excessive missing acks.
CPU Info:
CPU Model
Atheros AR7240 ver 1 rev 1.2 (0x00c2)
CPU Cores 1
CPU Clock 400 MHz
Memory Info:
Total Available
90%
29592 kB / 32768 kB
Free
39%
11544 kB / 29592 kB
Space Usage
NVRAM
15 KB / 64 KB
Something I noticed from last build to this build, when flashing via Telnet (unless I'm going crazy ), during wget operation, it shows nice ascii animation until % downloaded reaches 100. Also writing firmware via telnet shows written blocks differently. Traffic monthly monitoring & bandwidth monitoring graphs also working. Thank You Devs!
UPDATE: 3/28/2016
I have recently noticed that certain wireless devices are getting kicked out and not reconnecting, or needed manual reconnect and ipconfig/renew. AT first I thought my Dlink 615-E3 was failing, so I swapped out with WR842NDv1,but same issue happens
sample syslog from my wr842ndv1 unit, likely same error experienced from dlink 615E3
Mar 28 13:34:20 DD-WRT daemon.info hostapd: ath0: STA MAC:ADDRESS IEEE 802.11: disconnected due to excessive missing ACKs
Mar 28 13:34:49 DD-WRT daemon.info hostapd: ath0: STA MAC:ADDRESS IEEE 802.11: authenticated
Mar 28 13:34:49 DD-WRT daemon.info hostapd: ath0: STA MAC:ADDRESS IEEE 802.11: associated (aid 2)
Mar 28 13:34:49 DD-WRT daemon.info hostapd: ath0: STA MAC:ADDRESS RADIUS: starting accounting session 58D46ACD-00000068
Mar 28 13:34:49 DD-WRT daemon.info hostapd: ath0: STA MAC:ADDRESS WPA: pairwise key handshake completed (RSN)
Mar 28 13:35:07 DD-WRT daemon.info hostapd: ath0: STA MAC:ADDRESS IEEE 802.11: disconnected due to excessive missing ACKs
Last edited by gadgetpig on Tue Mar 28, 2017 13:52; edited 3 times in total
Joined: 05 Oct 2016 Posts: 19 Location: Bremen, Germany
Posted: Wed Mar 22, 2017 21:49 Post subject:
Router: TP-Link TL-WDR4900 V1.3
Firmware: DD-WRT v3.0-r31722 std (03/21/17)
Kernel: Linux 4.4.55 #278 Tue Mar 21 10:43:09 CET 2017 pp
Status: OK, but...
Reset: Yes
Errors: LAN-Port #4 not working?
I was on r30631 since last year, I really had trouble with some releases last year and had a bad impression of the recent versions...
This one seems to be ok but I am really confused, why LAN-Port #4 is not working. LED lids when I connect, but receive nothing from the router with this port.
Seems weird - never had any issue with this port before the update.
Is it possible that a bug in r31722 affects this one port?
Joined: 03 Jan 2010 Posts: 7568 Location: YWG, Canada
Posted: Thu Mar 23, 2017 0:56 Post subject:
Millhouse77 wrote:
Router: TP-Link TL-WDR4900 V1.3
Firmware: DD-WRT v3.0-r31722 std (03/21/17)
Kernel: Linux 4.4.55 #278 Tue Mar 21 10:43:09 CET 2017 pp
Status: OK, but...
Reset: Yes
Errors: LAN-Port #4 not working?
I was on r30631 since last year, I really had trouble with some releases last year and had a bad impression of the recent versions...
This one seems to be ok but I am really confused, why LAN-Port #4 is not working. LED lids when I connect, but receive nothing from the router with this port.
Seems weird - never had any issue with this port before the update.
Is it possible that a bug in r31722 affects this one port?
try stock fw, if its still dead its a failing switch & its not the rarest thing to happen on a router. _________________ LATEST FIRMWARE(S)
BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers
Router TPLINK WR1043ND V2
Firmware DD-WRT v3.0-r31722 std (03/21/17)
Kernel Version Linux 3.18.48 #2571 Tue Mar 21 05:51:04 CET 2017 mips
Status: Not Okay
Reset: yes
Errors: yes
Saving or Applying DDNS settings breaks GUI, and still does not save or apply.
Remote logging not working.
Update: Downgraded to r31277 applied settings then upgraded to r31722 again without reset.
Everything is working now but still saving or applying settings on DDNS page breaks GUI. So I can't make any changes to DDNS.