Author
Message
vpritiskovic DD-WRT User Joined: 28 Aug 2009 Posts: 248 Location: Dalmatia, Croatia
Posted: Sat Dec 17, 2011 18:55 Post subject: [lantiq][danube][sx763] support request
Since there is initial support for lantiq - http://www.dd-wrt.com/site/content/first-adsl-router-with-dd-wrt-support it would be nice to have dd-wrt on this danube xway target.
HW highligts:
atheros WiFi / DSL port / 1 USB / 4 LAN ports / 32MB RAM / 8MB flash
HW detection already done:
http://wiki.openwrt.org/toh/gigaset/sx76x
Ready to donate the device/s to dev's
OpenWrt bootlog:
Code: [ 0.000000] Linux version 3.1.3 (bevandur@spalato) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #3 Sat Dec 3 10:56:51 CET 2011
[ 0.000000] SoC: Danube rev 1.3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019641 (MIPS 24Kc)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 802894a0, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8128 pages, LIFO batch:0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: console=ttyLTQ1,115200 rootfstype=squashfs,jffs2 machtype=GIGASX76X
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=0002c138
[ 0.000000] Readback ErrCtl register=0002c138
[ 0.000000] Memory: 29560k/32768k available (2214k kernel code, 3208k reserved, 376k data, 168k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 333MHz
[ 0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
[ 0.040000] pid_max: default: 32768 minimum: 301
[ 0.044000] Mount-cache hash table entries: 512
[ 0.052000] NET: Registered protocol family 16
[ 0.064000] MIPS: machine is GIGASX76X - Gigaset SX761,SX762,SX763
[ 0.080000] GIGASX76X: Found ethernet MAC address: 00:XX:XX:XX:XX:XX.
[ 0.084000] GIGASX76X: Board id is sx763.
[ 0.104000] bio: create slab <bio-0> at 0
[ 0.112000] pci 0000:00:0e.0: [168c:ff16] type 0 class 0x000200
[ 0.112000] pci 0000:00:0e.0: reg 10: [mem 0x00000000-0x0000ffff]
[ 0.112000] pci 0000:00:0e.1: [168c:ff96] type 0 class 0x000700
[ 0.112000] pci 0000:00:0e.1: reg 10: [io 0x0000-0x0007]
[ 0.112000] pci 0000:00:0e.1: reg 14: [mem 0x00000000-0x00000fff]
[ 0.112000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
[ 0.116000] pci 0000:00:0e.0: BAR 0: set to [mem 0x18000000-0x1800ffff] (PCI address [0x18000000-0x1800ffff])
[ 0.120000] pci 0000:00:0e.1: BAR 1: assigned [mem 0x18010000-0x18010fff]
[ 0.124000] pci 0000:00:0e.1: BAR 1: set to [mem 0x18010000-0x18010fff] (PCI address [0x18010000-0x18010fff])
[ 0.128000] pci 0000:00:0e.1: BAR 0: assigned [io 0x1ae00000-0x1ae00007]
[ 0.132000] pci 0000:00:0e.1: BAR 0: set to [io 0x1ae00000-0x1ae00007] (PCI address [0x1ae00000-0x1ae00007])
[ 0.136000] Switching to clocksource MIPS
[ 0.144000] NET: Registered protocol family 2
[ 0.148000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.156000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.164000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.172000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.176000] TCP reno registered
[ 0.180000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.188000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.192000] NET: Registered protocol family 1
[ 0.196000] PCI: CLS 0 bytes, default 32
[ 0.200000] gptu: totally 6 16-bit timers/counters
[ 0.204000] gptu: misc_register on minor 63
[ 0.208000] gptu: succeeded to request irq 126
[ 0.212000] gptu: succeeded to request irq 127
[ 0.216000] gptu: succeeded to request irq 128
[ 0.220000] gptu: succeeded to request irq 129
[ 0.224000] gptu: succeeded to request irq 130
[ 0.232000] gptu: succeeded to request irq 131
[ 0.240000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.244000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.256000] msgmni has been set to 57
[ 0.260000] io scheduler noop registered
[ 0.264000] io scheduler deadline registered (default)
[ 0.268000] ltq_asc.0: ttyLTQ0 at MMIO 0x1e100400 (irq = 104) is a ltq_asc
[ 0.276000] ltq_asc.1: ttyLTQ1 at MMIO 0x1e100c00 (irq = 112) is a ltq_asc
[ 0.284000] console [ttyLTQ1] enabled, bootconsole disabled
[ 0.300000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001000
[ 0.308000] ltq_nor: Found an alias at 0x800000 for the chip at 0x0
[ 0.308000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.312000] Amd/Fujitsu Extended Query version 1.3.
[ 0.316000] number of CFI chips: 1
[ 0.320000] Creating 4 MTD partitions on "ltq_nor":
[ 0.324000] 0x000000000000-0x000000010000 : "uboot"
[ 0.332000] 0x000000010000-0x000000020000 : "uboot_env"
[ 0.340000] 0x000000020000-0x0000007f0000 : "linux"
[ 0.344000] Creating 2 MTD partitions on "ltq_nor":
[ 0.348000] 0x000000020000-0x0000001066af : "kernel"
[ 0.352000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.368000] 0x0000001066af-0x0000007f0000 : "rootfs"
[ 0.372000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.388000] mtd: partition "rootfs" set to be root filesystem
[ 0.392000] mtd: partition "rootfs_data" created automatically, ofs=440000, len=3B0000
[ 0.400000] 0x000000440000-0x0000007f0000 : "rootfs_data"
[ 0.408000] 0x0000007f0000-0x000000800000 : "board_config"
[ 0.464000] ltq_mii: probed
[ 0.464000] eth0: ADM6996M model PHY found.
[ 0.472000] eth0: attached PHY [Infineon ADM6996] (phy_addr=0:00, irq=-1)
[ 0.480000] Registered led device: soc:green:usb
[ 0.480000] Registered led device: soc:green:wifi
[ 0.480000] Registered led device: soc:green:phone2
[ 0.484000] Registered led device: soc:green:phone1
[ 0.484000] Registered led device: soc:green:line
[ 0.484000] Registered led device: soc:green:online
[ 0.484000] Registered led device: soc:green:voip
[ 0.484000] TCP westwood registered
[ 0.488000] NET: Registered protocol family 17
[ 0.492000] 8021q: 802.1Q VLAN Support v1.8
[ 0.512000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 0.520000] Freeing unused kernel memory: 168k freed
[ 6.796000] JFFS2 notice: (452) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 6 of xref (0 dead, 2 orphan) found.
[ 7.464000] SCSI subsystem initialized
[ 7.656000] usbcore: registered new interface driver usbfs
[ 7.660000] usbcore: registered new interface driver hub
[ 7.672000] usbcore: registered new device driver usb
[ 8.540000] Initializing USB Mass Storage driver...
[ 8.544000] usbcore: registered new interface driver usb-storage
[ 8.552000] USB Mass Storage support registered.
[ 30.780000] Compat-wireless backport release: compat-wireless-2011-11-08-1-g4ab9b62
[ 30.788000] Backport based on wireless-testing.git master-2011-11-15
[ 31.020000] cfg80211: Calling CRDA to update world regulatory domain
[ 31.724000] cfg80211: World regulatory domain updated:
[ 31.728000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 31.736000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 31.744000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 31.752000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 31.760000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 31.768000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 32.568000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
[ 32.572000] ath5k 0000:00:0e.0: registered as 'phy0'
[ 32.580000] ath: EEPROM regdomain: 0x37
[ 32.580000] ath: EEPROM indicates we should expect a direct regpair map
[ 32.580000] ath: Country alpha2 being used: AW
[ 32.580000] ath: Regpair used: 0x37
[ 32.580000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 32.584000] ath5k phy0: Atheros AR2414 chip found (MAC: 0x79, PHY: 0x45)
[ 32.592000] cfg80211: Calling CRDA for country: AW
[ 32.648000] NET: Registered protocol family 8
[ 32.648000] NET: Registered protocol family 20
[ 32.716000] cfg80211: Regulatory domain changed to country: AW
[ 32.720000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 32.728000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 32.736000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 32.744000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 32.752000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[ 32.772000] Button Hotplug driver version 0.4.1
[ 33.232000] PPP generic driver version 2.4.2
[ 33.568000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 33.852000] NET: Registered protocol family 24
[ 33.996000] nf_conntrack version 0.5.0 (464 buckets, 1856 max)
[ 34.612000] IFX MEI Version 5.00.00
[ 34.780000]
[ 34.780000] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
[ 34.820000] ATM (A1) firmware version 1.0.19
[ 34.820000] ifxmips_atm: ATM init succeed
[ 34.920000] dwc_otg: version 2.60a 22-NOV-2006
[ 35.524000] DWC_otg: Using DMA mode
[ 35.524000] dwc_otg dwc_otg.0: DWC OTG Controller
[ 35.532000] dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 1
[ 35.536000] dwc_otg dwc_otg.0: irq 62, io mem 0xffffffffbe101000
[ 35.548000] DWC_otg: Init: Port Power? op_state=1
[ 35.548000] DWC_otg: Init: Power Port (0)
[ 35.556000] hub 1-0:1.0: USB hub found
[ 35.556000] hub 1-0:1.0: 1 port detected
[ 35.684000] usbcore: registered new interface driver ums-alauda
[ 35.712000] usbcore: registered new interface driver ums-cypress
[ 35.740000] usbcore: registered new interface driver ums-datafab
[ 35.768000] usbcore: registered new interface driver ums-freecom
[ 35.864000] usbcore: registered new interface driver ums-isd200
[ 35.900000] usbcore: registered new interface driver ums-jumpshot
[ 35.936000] usbcore: registered new interface driver ums-karma
[ 35.952000] usb 1-1: new high speed USB device number 2 using dwc_otg
[ 36.040000] usbcore: registered new interface driver ums-sddr09
[ 36.076000] usbcore: registered new interface driver ums-sddr55
[ 36.180000] usbcore: registered new interface driver ums-usbat
[ 36.204000] scsi0 : usb-storage 1-1:1.0
[ 36.296000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
[ 37.240000] scsi 0:0:0:0: Direct-Access USB FLASH DRIVE PMAP PQ: 0 ANSI: 0 CCS
[ 37.264000] scsi: killing requests for dead queue
[ 38.396000] scsi: killing requests for dead queue
[ 38.404000] sd 0:0:0:0: [sda] 3915776 512-byte logical blocks: (2.00 GB/1.86 GiB)
[ 38.416000] scsi: killing requests for dead queue
[ 38.420000] sd 0:0:0:0: [sda] Write Protect is off
[ 38.424000] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
[ 38.424000] scsi: killing requests for dead queue
[ 38.440000] sd 0:0:0:0: [sda] No Caching mode page present
[ 38.444000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 38.452000] scsi: killing requests for dead queue
[ 38.456000] scsi: killing requests for dead queue
[ 38.472000] scsi: killing requests for dead queue
[ 38.476000] scsi: killing requests for dead queue
[ 38.492000] sd 0:0:0:0: [sda] No Caching mode page present
[ 38.496000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 38.528000] sda: sda1
[ 38.540000] sd 0:0:0:0: [sda] No Caching mode page present
[ 38.544000] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 38.552000] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 39.612000] device eth0.1 entered promiscuous mode
[ 39.616000] device eth0 entered promiscuous mode
[ 39.712000] br-lan: port 1(eth0.1) entering forwarding state
[ 39.716000] br-lan: port 1(eth0.1) entering forwarding state
[ 41.952000] cfg80211: Calling CRDA for country: HR
[ 44.056000] device wlan0 entered promiscuous mode
[ 44.060000] br-lan: port 2(wlan0) entering forwarding state
[ 44.064000] br-lan: port 2(wlan0) entering forwarding state
[ 45.104000] cfg80211: Calling CRDA to update world regulatory domain
[ 47.052000] cfg80211: World regulatory domain updated:
[ 47.056000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 47.064000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 47.072000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 47.080000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 47.088000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 47.096000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 47.104000] cfg80211: Calling CRDA for country: HR
[ 47.360000] device wlan0 left promiscuous mode
[ 47.360000] br-lan: port 2(wlan0) entering forwarding state
[ 47.396000] cfg80211: Regulatory domain changed to country: HR
[ 47.400000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 47.408000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 47.416000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 47.424000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 47.432000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[ 47.692000] device wlan0 entered promiscuous mode
[ 47.696000] br-lan: port 2(wlan0) entering forwarding state
[ 47.704000] br-lan: port 2(wlan0) entering forwarding state
[ 49.644000] Trying 100/FULL
[ 116.372000] [DSL_BSP_Showtime 916]: Datarate US intl = 319800, fast = 0
_________________DD-WRT v24-sp2 (01/21/12) std - build 18613 @SX763
DD-WRT v24-sp2 (10/12/12) std - build 20119 @WZR-HP-G300NH (b0 b0)
Back to top
Sponsor
zocra DD-WRT Novice Joined: 14 Jan 2007 Posts: 2
Posted: Sat Dec 17, 2011 19:15 Post subject:
It would be good to have the device with the ddwrt
Back to top
oskreso DD-WRT Novice Joined: 17 Dec 2011 Posts: 11
Posted: Sat Dec 17, 2011 21:13 Post subject: SX763
zocra wrote: It would be good to have the device with the ddwrt
Man, I couldn't agree more. Can't wait to have dd-wrt developed for rhis hardware. I am willing to donate one piece or to test firmware.
Back to top
Sash DD-WRT Guru Joined: 20 Sep 2006 Posts: 17619 Location: Hesse/Germany
Back to top
oskreso DD-WRT Novice Joined: 17 Dec 2011 Posts: 11
Posted: Sun Dec 18, 2011 12:17 Post subject:
Sash wrote: donate hw.
the buffalo was ported cause buffalo payed for it.
To whom should I donate hardware?
Back to top
DasShrubber2 DD-WRT User Joined: 31 Oct 2011 Posts: 61
Back to top
BrainSlayer Site Admin Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Thu Dec 22, 2011 11:46 Post subject:
as soon as i get it i will work on it. should be a easy task _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Back to top
vpritiskovic DD-WRT User Joined: 28 Aug 2009 Posts: 248 Location: Dalmatia, Croatia
Back to top
vpritiskovic DD-WRT User Joined: 28 Aug 2009 Posts: 248 Location: Dalmatia, Croatia
Back to top
Revenger_HR DD-WRT Novice Joined: 18 Jan 2012 Posts: 9
Posted: Wed Jan 18, 2012 19:20 Post subject:
+1
I would like to see this happen very much!
Back to top
Revenger_HR DD-WRT Novice Joined: 18 Jan 2012 Posts: 9
Posted: Thu Jan 19, 2012 12:39 Post subject:
BrainSlayer, did you get the device?
Back to top
Sash DD-WRT Guru Joined: 20 Sep 2006 Posts: 17619 Location: Hesse/Germany
Back to top
Revenger_HR DD-WRT Novice Joined: 18 Jan 2012 Posts: 9
Posted: Thu Jan 19, 2012 16:41 Post subject:
niceee... when roughly can we expect first build?
Back to top
vpritiskovic DD-WRT User Joined: 28 Aug 2009 Posts: 248 Location: Dalmatia, Croatia
Back to top
BrainSlayer Site Admin Joined: 06 Jun 2006 Posts: 7492 Location: Dresden, Germany
Posted: Sat Jan 21, 2012 10:47 Post subject:
you got mail with additional fixes. _________________ "So you tried to use the computer and it started smoking? Sounds like a Mac to me.." - Louis Rossmann https://www.youtube.com/watch?v=eL_5YDRWqGE&t=60s
Back to top