Anyone else having this issues with AR670W?
Should I open a new ticket just for AR670W?
Brain Slayer: Would the same fix for the 690 be easy for you to apply to 670?
It is enough that you have added AR670 to ticket #2040.
The AR690 problem is not related to this, AR690 has a different ethernet switch.
Thank you, LOM. Both your answers make good sense. Appreciate your quick reply.
Time-permitting I'm considering adding tty/com port to one of my 670's in order to capture and post linux system start messages, would this be helpful?
I see the number of models, and people, affected by this issue is increasing. Hope soon we'll reach the critical mass that triggers a corrective action. Keep the reports coming
Posted: Sat Sep 24, 2011 10:28 Post subject: Re: LAN ports broken AR670W r16454, r16754, r16994 & r17
scrotar wrote:
Using 30-30-30 re-flash process the following releases all result in LAN ports not working on AR670W:
(same problem on two different AR670's)
03-17-11-r16454 same problem
04-09-11-r16754 same problem
05-08-11-r16994 same problem
(I did not try 04-09-11-r16785)
06-14-11-r17201 same problem
Are you completely sure that 16454 has the problem?
There is just one minor change of the source code for Ralink between 16214 and 16454, that change should not break the lan port functionality. _________________ Kernel panic: Aiee, killing interrupt handler!
Are you completely sure that 16454 has the problem?
There is just one minor change of the source code for Ralink between 16214 and 16454, that change should not break the lan port functionality.
jons wrote:
Happens to me too with my Senao/Encore ESR9753
Build 16454 and up.
I'll make time this week to give another try on my AR670W with r16454 (just to be absolutely certain that it breaks the LAN ports).
Are you completely sure that 16454 has the problem?
There is just one minor change of the source code for Ralink between 16214 and 16454, that change should not break the lan port functionality.
jons wrote:
Happens to me too with my Senao/Encore ESR9753
Build 16454 and up.
I'll make time this week to give another try on my AR670W with r16454 (just to be absolutely certain that it breaks the LAN ports).
scrotar
I flashed my AR670W with r16454 and LAN ports seem to be working fine I didn't do a 30-30-30 (kept existing settings), I'll try it again with a 30-30-30 next just to be sure that all is well with LAN ports.
In the mean time, anyone know if sshd is broken in r16454? (can't get it running, gives me this error authpriv.info dropbear[8692]: Premature exit: String too long)
Are you completely sure that 16454 has the problem?
There is just one minor change of the source code for Ralink between 16214 and 16454, that change should not break the lan port functionality.
jons wrote:
Happens to me too with my Senao/Encore ESR9753
Build 16454 and up.
I'll make time this week to give another try on my AR670W with r16454 (just to be absolutely certain that it breaks the LAN ports).
scrotar
I flashed my AR670W with r16454 and LAN ports seem to be working fine I didn't do a 30-30-30 (kept existing settings), I'll try it again with a 30-30-30 next just to be sure that all is well with LAN ports.
In the mean time, anyone know if sshd is broken in r16454? (can't get it running, gives me this error authpriv.info dropbear[8692]: Premature exit: String too long)
Flashed these builds again (was lazy and kept settings)
03-17-11-r16454 LAN ports work but dropbear issues as above.
04-09-11-r16754 LAN ports definitely broken.
The dropbear issues I mentioned above turns out to be a known issues, bug was tracked and closed in new release (sheesh i'm making some really lazy/newb mistakes in this thread).
LOM wrote:
ok, I have not checked for changes to the router software - only changes to the kernel.
16454 is then ok on the LAN switch.
16754 and 16785 are too big in size
16994 is ok in size but there may be other problems with it.
LOM: I'm not sure what you mean by 'too big in size'.
Toady I logged AR670W console boot messages from serial port. I noted a couple differences between working r16214 and LAN not working r17201. I'm not sure if these excerpts helps, if complete boot up details will be more helpful I will post. I have BOLDED the differences I noted when booting r17201.
BOOTING r16214
##############
Linux version 2.6.23.17 (root@dd-wrt) (gcc version 4.1.2) #5972 Thu Feb 17 10:09:31 CET 2011
Load Ralink DFS Timer Module
devfs: 2004-01-31 Richard Gooch (rgooch@…)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
Ralink gpio driver initialized
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xa0300500 (irq = 9) is a 16550A
serial8250: ttyS1 at I/O 0xa0300c00 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@…>
ralink flash device: 0x400000 at 0xbf000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu? Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
found squashfs at 118000
Creating 6 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00030000 : "uboot"
0x00030000-0x00040000 : "uboot-config"
0x00040000-0x00050000 : "factory-defaults"
0x00040000-0x003f0000 : "linux"
0x00118000-0x003f0000 : "rootfs"
BOOTING r17201
##############
Linux version 2.6.23.17 (root@dd-wrt) (gcc version 4.5.2 (Linaro GCC 4.5-2011.02-0) ) #7021 Sun May 8 11:55:42 CEST 2011
Load Ralink DFS Timer Module
devfs: 2004-01-31 Richard Gooch (rgooch@…)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
Ralink gpio driver initialized
spidrv_major = 217
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xa0300500 (irq = 9) is a 16550A
serial8250: ttyS1 at I/O 0xa0300c00 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@…>
ralink flash device: 0x400000 at 0xbf000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16/bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-arptables: nonexistent directory
/bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-ip6tables: nonexistent directory
/bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-iptables: nonexistent directory
/bin/sh: ead: not found
wland: No such file or directory
Board: RT2880 DRAM: 32 MB
twe0 set to <NULL>
toe0 set to <NULL>
Set up sector start address BC400000
*** Warning - bad CRC, using default environment
============================================
ASIC -VerB/C (MAC to Phy Mode)
DRAM COMPONENT=128Mbits
DRAM BUS=32BIT
Total memory = 32Mbytes
Date:Oct 3 2007 Time:16:02:26
============================================
Eth0 (10/100-M)
Hit any key to stop autoboot: 0
## Booting image at bc440000 ...
Image Name: 7zip Linux Kernel
Created: 1970-01-01 0:00:00 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: -1 Bytes = 4096 MB
Load Address: 8a000000
Entry Point: 8a000000
Uncompressing Kernel Image with LZMA ... OK
Starting kernel ...
LINUX started...
THIS IS ASIC
Linux version 2.6.23.17 (root@dd-wrt) (gcc version 4.5.4 20110526 (prerelease) (Linaro GCC 4.5-2011.06-0) ) #2576 Wed Dec 14 09:48:21 CET 2011
The CPU frequency set to 266 MHz
32M RAM Detected!
CPU revision is: 0001906c
Determined physical RAM map:
memory: 02000000 @ 08000000 (usable)
Wasting 1048576 bytes for tracking 32768 unused pages
Built 1 zonelists in Zone order. Total pages: 40640
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4 rootfstype=squashfs noinitrd
Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 16kB, 4-way, linesize 16 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
cause = 90800024, status = 1000ff00
PID hash table entries: 1024 (order: 10, 4096 bytes)
calculating r4koff... 0028b0aa(2666666)
CPU frequency 266.67 MHz
Using 133.333 MHz high precision timer.
console [ttyS1] enabled
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 28032k/32768k available (2331k kernel code, 4644k reserved, 316k data, 116k init, 0k highmem)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Generic PHY: Registered new driver
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
Load Ralink DFS Timer Module
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
io scheduler noop registered
io scheduler deadline registered (default)
Ralink gpio driver initialized
spidrv_major = 217
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xa0300500 (irq = 9) is a 16550A
serial8250: ttyS1 at I/O 0xa0300c00 (irq = 8) is a 16550A
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ralink flash device: 0x400000 at 0xbf000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
found squashfs at 11C000
Creating 6 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00030000 : "uboot"
0x00030000-0x00040000 : "uboot-config"
0x00040000-0x00050000 : "factory-defaults"
0x00040000-0x003f0000 : "linux"
0x0011c000-0x003f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
0x003f0000-0x00400000 : "nvram"
Ralink APSoC Hardware Watchdog Timer
u32 classifier
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
ctnetlink v0.93: registering with nfnetlink.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
IPP2P v0.8.2 loading
ClusterIP Version 0.8 loaded successfully
TCP bic registered
TCP cubic registered
TCP westwood registered
TCP highspeed registered
TCP hybla registered
TCP htcp registered
TCP vegas registered
TCP scalable registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Welcome to PF_RING 3.2.1
(C) 2004-06 L.Deri <deri@ntop.org>
NET: Registered protocol family 27
PF_RING: bucket length 128 bytes
PF_RING: ring slots 4096
PF_RING: sample rate 1 [1=no sampling]
PF_RING: capture TX No [RX only]
PF_RING: transparent mode Yes
PF_RING initialized correctly.
PF_RING: registered /proc/net/pf_ring/
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
MAC_ADRH -- : 0x00000000
MAC_ADRL -- : 0x00000000