[movozo]

2610 did not change much.
Still: use Secondary for external. Primary for internal. And of course, set the Hardware-Swtich the right way.

The dd-wrt guys will get more Hardware Info from Senao and will report us.

[enrico1301]

Hi
Some new test:
Outdoor test 100/120m distance, A.P. 9m height
read info every 2 secs

Senao EOC-1650 original firmaware (last version) 20db external antenna.

link quality: 42/100 42/100 45/100
signal level: -73 -75 -73 dBm
noise level: -90 -92 -91 dBm
SNR: 17 17 18 db

Senao EOC-1650 dd-wrt(26032009) 20db external antenna.

link quality: 20/100 20/100 17/100
signal level: -87 -86 -87 dBm
noise level: -95 -94 -94 dBm
SNR: 8 8 7 db

Buffalo WHR-HP-G54 with omnidirectional antenna 4dbi 70mw V24SP1

link quality: 60/100 37/100 42/100
signal level: -72 -79 -78 dBm
noise level: -96 -94 -95 dBm
SNR: 24 15 17 db

[darknforce]

Anybody tested the new released?

v24presp2Build11898 2009-04-09 6,54 MB

[barlabota]

Good boys I have updated to the version 09042009 of 2610 and have proved(tried) exterior(foreign) antenna without ningun result is all the same that he(she) places it does not notice any profit, only I have selected exterior in the Eoc since the filware does not have option of secondary.
It(He,She) waits of solution

[darknforce]

[gestur]

I've done some testing and I saw the following:

Using a NS2 as AP and a Senao 2610 as client bridge.

If I set NS2 channel to 1, the Senao connects fine, but with irregular data rates even with 50 RSI. Tried diferent power levels in both sides. The rate varies a lot when changing channels.

But I saw that using channel 3 in the ap causes the Senao to connect at channel 4 with 1-2 Mbps datarates. Same in channel 4,5,6, it connects to the following channel with bad datarates. I rebooted the Senao to see if it connects correcly but it doesn't.

Using channel 11 works fine but with irregular and asymmetric datarates.

So i think that all the channels in the Senao 2610 could be shifted 5 or 10 MHz up. Considering the lack of hardware information about the Senao I think this be a clue about the problem with the Senaos.

[Sash]

ok info that misses here:

ns2 firmware and version
senaao firmware and version
reg dom of the 2 (that could be the cause of thee probs)
connection mode of the 2
and many more that could cause the problems...

[darknforce]

The new firmware works great i think u fix the TX power settings but i'm currently facing WDS problem

If i put more than 2 WDS inside the EOC-2610 settings the AP will goes haywired and crazy

With 2 WDS settings inside it the AP should be running fine with no problems at all.

Hope brainslayer check this problem regarding WDS

I'm running on 09/04/2009 firmware

[Sash]

no

wiki: wds

[barlabota]

Sash.

We know since(as,like) there goes the improvement of the power of the antenna in the Senao I need to be able to return an alpha 5oomW that have given me to realize a few tests(proofs) and this one overcomes clearly the power of the senao 2610 .

Regards

[barlabota]

???????Is not it known at all?

[DjStraw]

Put external or internal antenna in the last firmware?

[Sash]

guys have u tried the latest build?

[davidhtn]

With the factory firmware shipped with the EOC-1650, I was able to connect to access points almost a mile away as a client bridge, after installing dd-wrt and PAYING to activate it, I can no longer see those access points.

So tell me, did I just turn my outdoor bridge into a short range indoor ap? because that is about all it is good for.

also the web interface takes FOREVER to respond page to page.

I'm not sure dd-wrt is the smartest option with this unit, and that is an issue considering there is no way to return to factory settings.