just more problems added, existing ones remain, ath10k beamforming only half works, qos netmask broken etc.. just avoid this build... _________________ LATEST FIRMWARE(S)
BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers
Router: TPLINK WR1043ND V3
Firmware: DD-WRT v3.0-r33257 (08/29/17)
Kernel: Linux 3.18.67 #9695 Tue Aug 29 03:25:29 CEST 2017 mips
Status: OK
Reset: 2x
Errors: None so far
Joined: 24 Feb 2013 Posts: 1634 Location: Belgrade
Posted: Wed Aug 30, 2017 18:12 Post subject:
Router ModelGL.iNet-AR150
Firmware Version DD-WRT v3.0-r33257 std (08/29/17)
Kernel VersionLinux 3.18.67 #9727 Tue Aug 29 04:41:17 CEST 2017 mips
Status: OK (OpenVPN server, VAP, IPv6 HE tunnel, Time Restrictions WiFi scheduler, DDNS etc.)
Reset: no
Errors: None, just misconfigurations. Thx BS
suggestion: OpenVPN log tab is much better than Syslog tab. Font is smaller and you can scroll down as much as you want. I would import it from OVPN tab... then when something is critical in syslog RED colour is VERY strong and it is not readable...
Router: DIR-615 i1
Status: Good
Reset: Reset to defaults with flash procedure; erased NVRAM before and after flash
Errors: None
Router: TL-WDR3600 v. 1.5
Status: Buggy
Reset: Reset to defaults with flash procedure; erased NVRAM before and after flash
Errors: Router is randomly rebooting starting with r33215. I noticed I can't even get 24 hours of uptime with the last two builds. Flashed back to r33180.
EA8500
DD-WRT v3.0-r33257 (08/29/17)
Linux 3.18.67 #172 SMP PREEMPT Sat Aug 26 18:20:45 CEST 2017 armv7l
installed over r23253
twas in a WDS setup on 5GHz and still working after.
Reset w/WAN connected to main
QOS global downlink setting does absolutely nothing .. wide open no matter the setting.
uplink working ok
verified SFE module not running
test w/iperf3 to main (EA8500 r33215) & reverse send.
Reset w/WAN connected to main
QOS global downlink setting does absolutely nothing .. wide open no matter the setting.
uplink working ok
verified SFE module not running
test w/iperf3 to main (EA8500 r33215) & reverse send.
WTH ??¿¿ ..ummmm..... that is really NOT true you goofus.
iperf3 send from server bypasses QOS you dummy.
So QOS global settings seem somewhat intact, ok....geezs, stuff you can read in this place
Status: OK
Reset: none
Errors: WDR4900 & Archer C7 V2.0 - SMB Server not working, USB devices not recognized after reboot, need to restart usb services ... only FTP works
TL-WDR3500 V1.2 crashing after 2 days , need reboot
just basic WDS AP (WDR4900) / WDS station setup
Last edited by hebeda on Tue Sep 05, 2017 10:15; edited 2 times in total
I was able to recover from unstable FW on this router before, and even from a bad flash, but this time, even while tftp (only thing that works) transfers the file, the router continuously reboots (All LAN lights turn on, then off, a little while, on then off and so on).
I tried 30-30-30 and tftp flashing various binaries, including the stock FW. Nothing.
I was able to recover from unstable FW on this router before, and even from a bad flash, but this time, even while tftp (only thing that works) transfers the file, the router continuously reboots (All LAN lights turn on, then off, a little while, on then off and so on).
I tried 30-30-30 and tftp flashing various binaries, including the stock FW. Nothing.
You really should be in the broadcom forum with the E1200v2.
You should really read new build threads.
You will need to open the box .... yea I try to avoid that also
Got to have a USB/TTL to connect up.
Get the CFE prompt and do "nvram erase"
Then do "flash -ctheader : flash1.trx
Got to have the TFTP setup to send ... I used the original E1200v2 Linksys firmware.
You can save her but you got to open the BOX!!!
or so it recovered from r33180 anyways
good luck -
If anyone is interested the serial log shows hang at 'checking USB ...' which the E1200v2
don't have but I reckon some of BS recent commits have runamuck
Joined: 12 May 2012 Posts: 66 Location: Rio Grande do Sul / Brasil
Posted: Sat Sep 02, 2017 18:59 Post subject:
Router: TP-Link -WDR4300 v1.8
Firmware: DD-WRT v3.0-r33257 std (08/29/17)
Kernel: Linux 3.10.107 #39019 Tue Aug 29 02:12:57 CEST 2017 mips
Status: OK
Reset: No
Errors: No
