This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 28397_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. PLEASE ALSO DO NOT RESPOND TO SUCH QUESTIONS! This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless.
If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build. _________________ [I prefer answere in whole sentence]
Your reports for Broadcom units are greatly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors: _________________ THERE ARE NO STRANGERS HERE; ONLY FRIENDS YOU HAVEN'T YET MET.
________________________________________________________________________________________________________
DD-WRT CHANGELOG | DEVICES | DD-WRT BUILDS | KONG BUILDS | UNOFFICIAL BUILDS | DD-WRT in VIRTUALBOX
Last edited by KrypteX on Tue Dec 01, 2015 23:06; edited 2 times in total
Router: EA6400
Firmware: DD-WRT v3.0-r28397 std (12/01/15)
Kernel: Linux 3.10.93 #5021 SMP Mon Nov 30 09:10:58 CET 2015 armv7l
Status: working
Reset: no
Errors: none yet
i've got xvortex cfe, so can only flash using ssh to upload image, and then mtd commands. but flash over r28366 was without problem. 2AP's working with good 5g and 2.4g signals, and virtual ssid's. site survey works on both bands.
Router: Netgear R7000
Firmware: DD-WRT v3.0-r28397 std (12/01/15)
Kernel: Linux 3.10.93 #5021 SMP Mon Nov 30 09:10:58 CET 2015 armv7l
Status: Working
Reset: No
Previous: 28366
Errors: No
Router: Netgear R7000
Firmware: DD-WRT v3.0-r28397 std (12/01/15)
Kernel: Linux 3.10.93 #5021 SMP Mon Nov 30 09:10:58 CET 2015 armv7l
Status: Working
Reset: No
Previous: 28374
Errors: No
Thx for your work
(off topic : hope a new Kong release will be available soon ) _________________ Unofficial Kong's release repository : http://ddwrt-kong.clonevince.fr/
Router: RT-AC87U - primary router/gateway
Firmware: asus_rt-ac87u-firmware.trx
Kernel: Linux 3.10.93 #5028 SMP Tue Dec 1 05:53:40 CET 2015 armv7l
2.4Ghz (NG-mixed) with 40Mhz channel width: OK
5Ghz (AC/N-Mixed) with 80Mhz channel width: OK
Guest-Vlan 2.4Ghz: OK
SSH: OK
Telnet: OK
Port Forward: OK
WOL over the Internet: OK
VNC Repeater: OK
USB 2.0 storage ext3 mount to JFFS: OK
USB 3.0 storage NTFS mount to MNT: OK
NAS Samba shared drive: NO on reboot, but hitting Apply Settings button in NAS tab will start it
PPTP Server: OK
Wi-viz 2.4Ghz & 5Ghz: 2.4Ghz OK – 5Ghz NO
Reset via GUI: Yes before and after upgrade
Status: Working (required a power boot after flash & reset)
Error(s): Guest network does not show any output signal, noise, or SNR in the wireless clients output table
Router: RT-AC68R - primary router/gateway
Firmware: asus_rt-ac68u-firmware.trx
Kernel: Linux 3.10.93 #5021 SMP Mon Nov 30 09:10:58 CET 2015 armv7l
2.4Ghz (NG-mixed) with 40Mhz channel width: OK
5Ghz (AC/N-Mixed) with 80Mhz channel width: OK
Guest-Vlan 2.4Ghz: OK
SSH: OK
Telnet: OK
Port Forward: OK
WOL over the Internet: OK
VNC Repeater: OK
USB 2.0 storage ext3 mount to JFFS: OK
USB 3.0 storage NTFS mount to MNT: OK
NAS Samba shared drive: OK
PPTP Server: OK
Wi-viz 2.4Ghz & 5Ghz: NO
Reset via GUI: Yes before and after upgrade
Status: Working
Error(s): Guest network does not show any output signal, noise, or SNR in the wireless clients output table
Repeater Bridge Build 28397 previous build 28366
Router: RT-AC66U - Repeater Bridge on 5 Ghz (AC-Only) to RT-AC87U
Firmware: dd-wrt-28397-Asus_RT-AC66.trx
Kernel: Linux 3.10.93 #10448 Tue Dec 1 08:55:50 CET 2015 mips
2.4Ghz (NG-mixed) with 20Mhz channel width: OK
5Ghz (AC-Only): OK
Reset via GUI: No
Status: Working
Error(s): OK
** Builds after 26339 when erasing NVRAM in telnet session or Power UP Reset, resets 5.0 GHz radio to 2.4 GHz radios – To recover return to 26339 ***
*** Builds after 26339 use the Administration >> Factory Defaults tab in the GUI to reset NVRAM ***
*** Since 27343 the following command needs to be included in the Start-up script, ‘sleep 5; startstop lan’ to allow the 5 Ghz to connect to the main AP in Repeater Bride mode when rebooting. Thanks to Magnetron 1.1 for putting in forum topic ***
Router: e4200 – Repeater Bridge on 5 Ghz (N) to RT-AC87U
Firmware: dd-wrt.v24-28397_NEWD-2_K3.x_mega-e4200.bin
Kernal: Linux 3.10.93 #10464 Tue Dec 1 09:08:39 CET 2015 mips
2.4Ghz (NG-mixed) with 20Mhz channel width: OK
5Ghz (N):OK
Reset via GUI: No
Status: Working
Error(s): OK
*** Since 27343 the following command needs to be included in the Start-up script, ‘sleep 5; startstop lan’ to allow the 5 Ghz to connect to the main AP in Repeater Bride mode when rebooting. Thanks to Magnetron 1.1 for putting in forum topic *** _________________ Netgear XR500, R7800
Asus AC87Ua1
Repeater Bridge
Netgear R6400v2otp
Router: EA6900
Firmware: linksys-ea6900-webflash.bin (r28397 12/01/15)
Kernel: Linux 3.10.93 #5021 SMP Mon Nov 30 09:10:58 CET 2015 armv7l
Status: working
Reset: no
Errors: no
Joined: 09 Nov 2014 Posts: 314 Location: Bakersfield, CA
Posted: Tue Dec 01, 2015 18:12 Post subject:
Router: 2x Linksys e3000
Firmware: dd-wrt.v24-28397_NEWD-2_K3.x_mega-e3000.bin
Previous: dd-wrt.v24-28211_NEWD-2_K3.x_mega-e3000.bin
Kernel: Linux 3.10.93 #10464 Tue Dec 1 09:08:39 CET 2015 mips
Status: Working GREAT as client bridges. Speed is back up, was a little slow on the last build.
Reset: No
Errors: None thus far _________________ Deployed Routers:
Netgear R7800 - 1x build 46979
- Gateway (USB /w Entware, CAKE QoS)
Netgear R7000 - 3x build 46979
Router: Linksys E3000
Firmware: DD-WRT v3.0-r28397 mega
Kernel: 3.10.93
Status: Working (DNSmasq issue)
Reset: No
Errors: Cannot connect to IPv6 enabled hosts via SOCKS (dynamic port forwarding) when remote DNS lookups are enabled even with IPv6 disabled in dd-wrt. I suspect DNSmasq has some IPv6 bits enabled even though IPv6 is completely disabled under Setup>IPv6.
Local lookup of IPv6 enabled host:
root@dd-wrt:~# nslookup www.google.ca
Server: (null)
Address 1: ::1 localhost
Address 2: 127.0.0.1 localhost
Joined: 09 Nov 2014 Posts: 314 Location: Bakersfield, CA
Posted: Tue Dec 01, 2015 19:34 Post subject:
Router: ASUS RT-N16
Firmware: dd-wrt.v24-28397_NEWD-2_K3.x_mega_RT-N16.trx
Previous: dd-wrt.v24-28211_NEWD-2_K3.x_mega_RT-N16.trx
Kernel: Linux 3.10.93 #10464 Tue Dec 1 09:08:39 CET 2015 mips
Status: Working
Reset: No
Errors: None thus far!
Router: Linksys EA6400
Firmware: DD-WRT v3.0-r28397 (12/01/15)
Kernel: Linux 3.10.93 #5021 SMP Mon Nov 30 09:10:58 CET 2015 armv7|
Status: Working
Reset: No
Errors:
- SSH Management can not be enabled
- Temperatures extremely high: CPU 108°C / WL0 50°C / WL1 57°C. Is the temperature of CPU not displayed in Fahrenheit (108°F = 44°C) ?
- Translation mistakes in French
- Can not make address reservation (Services / DHCP server) Only possible 1 by 1 with intermediate saving.
- Green top led not active
Router: Buffalo WZR-1750DHP
Firmware: DD-WRT v3.0-r28397 std (12/01/15)
Kernel: Linux 3.10.93 #5021 SMP Mon Nov 30 09:10:58 CET 2015 armv7l
Status: Mostly OK
Reset: No
Errors: IPv6 doesn't seem to work with Comcast anymore (worked with r28374
